Project Icon

Instrumentation and Measurement Projects

Instrumentation and Measurement Projects
Status Help
260.1 - Standard Letter Symbols for Units of Measurement (SI Units, Customary Inch-Pound Units, and Certain Other Units)The existing standard on unit symbols has been updated to conform to current international standard practices. An informative annex has ... active Project
260.4 - Standard Letter Symbols and Abbreviations for Quantities Used in AcousticsTo clarify the technical literature of acoustics by providing a standard set of letter symbols for use in mathematical formulations, and ... active Project
280 - Standard Letter Symbols for Quantities Used in Electrical Science and Electrical EngineeringThis standard covers letter symbols used to represent physical quantities in the field of electrical science and electrical engineering. ... active Project
287.1 - Standard for Precision Coaxial Connectors at RF, Microwave and Millimeter-wave FrequenciesThe purpose of this standard is to present minimum performance requirements for those precision connectors used at RF, microwave and mil ... active Project
287.2 - Recommended Practice for Precision Coaxial Connectors at RF, Microwave and Millimeter-wave Frequencies - Part 2: Test ProceduresThe purpose of this Recommended Practice is to present state-of-the-art test procedures that can be used to verify the performance of co ... active Project
287.3 - Recommended Practice for Precision Coaxial Connectors at RF, Microwave and Millimeter-wave Frequencies - Part 3: Connector Effects, Uncertainty Specifications and Recommendations for PerformanceThe purpose of this Recommended Practice is to present information and tools that will inform coaxial connector users and will enhance u ... active Project
378 - Recommended Practices for Scattering Parameter Measurements Using Vector Network AnalyzersProvide definitions of terms commonly used by users and manufacturers of vector network analyzers. Define and describe measurement techn ... active Project
656 - IEEE Draft Standard for the Measurement of Audible Noise from Overhead Transmission LinesUniform procedures are established for manual 1 and automatic measurement of audible noise from overhead transmission lines. Their purpo ... active Project
945 - Recommended Practice for Preferred Metric Units for Use in Electrical and Electronics Science and TechnologyThe purpose of this recommended practice is to aid in the selection of appropriate metric units for physical quantities that are of inte ... active Project
947 - Guide for Identification of Alternative Metric Devices for Valves, Fittings, Threads, FlangesThis document provides guidance to Standards Developers who would like a broader acceptance of the Standard they are developing for use ... active Project
1241 - Standard for Terminology and Test Methods for Analog-to-Digital ConvertersThis standard identifies ADC error sources and provides test methods with which to perform the required error measurements. The informat ... active Project
1450.4 - IEEE Draft Standard for Extensions to Standard Test Interface Language (STIL) (IEEE Std. 1450-1999) for Test Flow SpecificationThis standard extends IEEE Std 1450-1999 (STIL) to 39 provide an interface between test generation tools and test equipment with regard ... active Project
1451.8 - Standard for Wind Turbine Health Monitoring System Wireless Communication Protocols and Transducer Electronic Data Sheet (TEDS) FormatThis standard establishes wireless communication protocols and Transducer Electronic Data Sheet (TEDS) formats for acoustical wind turbi ... active Project
1451-99 - Standard for Harmonization of Internet of Things (IoT) Devices and SystemsThe purpose of this standard is to define a metadata bridge to facilitate IoT protocol transport for sensors, actuators, and devices. Th ... active Project
1505.1 - Standard for the Common Test Interface Pin Map Configuration for High-Density, Single-Tier Electronics Test Requirements Utilizing IEEE Std 1505Permits the physical interoperability of IEEE-1505 compliant interface fixtures (also known as interface test adapters, interface device ... active Project
1541 - Standard for Prefixes for Binary MultiplesThe prefixes kilo, mega, giga, etc. are defined by the SI Brochure, "International System of Units", and other international standards t ... active Project
1588 - Standard for a Precision Clock Synchronization Protocol for Networked Measurement and Control SystemsThis standard defines a network protocol enabling accurate and precise synchronization of the real-time clocks of devices in networked d ... active Project
1641 - Standard for Signal and Test DefinitionThis standard provides a common reference for signal definitions, which may be used throughout the life cycle of a unit under test (UUT) ... active Project
1671.1 - IEEE Draft Standard for Automatic Test Markup Language (ATML) Test DescriptionThis standard defines an exchange format, utilizing Extensible Markup Language (XML), for both the static description of unit under test ... active Project
1671.3 - IEEE Draft Standard for Automatic Test Markup Language (ATML) Unit Under Test (UUT) DescriptionNo purpose statement is required since this standard is intended for IEC standardization. active Project
1804 - IEEE Draft Standard for Fault Accounting and Coverage Reporting to Digital Modules (FACR)The standard formalizes aspects of fault models as they are relevant to the generation of test patterns for digital circuits. Its scope ... active Project
1838 - Standard for Test Access Architecture for Three-Dimensional Stacked Integrated CircuitsFor 3D-SICs, three parties are involved: Die Maker(s), Stack Maker(s), and Stack User(s). All circuit features of the stack are included ... active Project
2414 - Standard for Jitter and Phase NoiseThe purpose of the standard is to facilitate accurate and precise communication concerning jitter and phase noise and the methods for me ... active Project
2450 - Standard for the Performance of Down-the-Road Radar Used in Traffic Speed MeasurementsThe primary purpose of this standard is to ensure that there are a well-defined set of specifications and test methods so they can be us ... active Project
2452 - Standard for the Performance of Lidar Used in Traffic Speed MeasurementsThe primary purpose of this standard is to ensure that there are a well-defined set of specifications and test methods so they can be us ... active Project
3333.1.2 - IEEE Draft Standard for the Perceptual Quality Assessment of Three Dimensional (3D) and Ultra High Definition (UHD) ContentsThe world is witnessing a rapid advance in Stereoscopic 3D, and Ultra high definition (UHD) technology. As a result, the need for accura ... active Project
7009 - Standard for Fail-Safe Design of Autonomous and Semi-Autonomous SystemsThis standard establishes a practical, technical baseline of specific methodologies and tools for the development, implementation, and u ... active Project
21451-1 - Standard for Smart Transducer Interface for Sensors and Actuators - Common Network ServicesIn the family of IEEE 1451 standards, there are no common network services defined for IEEE 1451 smart transducers to communicate transd ... active Project
21451-1-4 - Standard for a Smart Transducer Interface for Sensors, Actuators, and Devices - eXtensible Messaging and Presence Protocol (XMPP) for Networked Device CommunicationThe purpose of this standard is to provide session initiation and protocol transport for sensors, actuators, and devices. The standard ... active Project
21451-1-5 - Standard for a Smart Transducer Interface for Sensors, Actuators, and Devices - Simple Network Management Protocol (SNMP) for Networked Device CommunicationThe purpose of this standard is to provide a simplified method to facilitate access of transducers to a network with structured data ind ... active Project
61869-105 - Recommended Practice for Uncertainty Evaluation in the Calibration of Instrument TransformersThis recommended practice defines a common viewpoint of the evaluation of uncertainty in calibration and its application in testing proc ... active Project