Project Icon

Industry Applications Projects

Displaying results 1 - 40 of 156
Project Name
StatusHelp
P11 - Rotating Electric Machinery for Rail and Road Vehicles The purpose of this standard is to define ratings, tests, and calculation procedures to permit comparison among machines for similar use, and to... Active Project
P18 - Shunt Power Capacitors This standard applies to power capacitors rated 216 V or higher, 2.5 kvar or more, and designed for shunt connection to alternating current... Active Project
P45.1 - Recommended Practice for Electrical Installations on Shipboard - Design An extension of the baseline technology and methods covered in IEEE Std 45, P45.1 provides a consensus of recommended practices for design in... Active Project
P45.4 - Recommended Practice for Electrical Installations on Shipboard - Marine Sectors and Mission Systems An extension of the baseline technology and methods covered in IEEE std 45, P45.4 provides a consensus of recommended practices for marine sectors... Active Project
P45.6 - Draft Recommended Practice for Electrical Installations on Shipboard - Electrical Testing Provides a consensus of recommended practices for system testing in marine electrical engineering as applied specifically to vessels, shipboard... Active Project
P48 - Test Procedures and Requirements for Alternating-Current Cable Terminations Used on Shielded Cables Having Laminated Insulation Rated 2.5 kV through 765 kV or Extruded Insulation Rated 2.5 kV through 500 kV This standard provides test procedures and requirements for all indoor and outdoor cable terminations used on alternating-current shielded cables... Active Project
P81 - Guide for Measuring Earth Resistivity, Ground Impedance, and Earth Surface Potentials of a Grounding System The purpose of this guide is to present practical instrumentation methods that may be used for measuring soil resistivity, the impedance to remote... Active Project
P99 - Recommended Practice for the Preparation of Test Procedures for the Thermal Evaluation of Insulation Systems for Electrical Equipment This recommended practice provides a general format for the preparation of test procedures and suggests the points to be considered by technical... Active Project
P112 - Draft Standard Test Procedure for Polyphase Induction Motors and Generators Instructions for conducting and reporting the more generally applicable and acceptable tests of polyphase induction motors and generators are covered. Active Project
P115 - Guide for Test Procedures for Synchronous Machines Part I-Acceptance and Performance Testing Part II-Test Procedures and Parameter Determination for Dynamic Analysis This guide contains instructions for conducting generally applicable and accepted tests to determine the performance characteristics of... Active Project
P149 - Recommended Practice for Antenna Measurements The purpose is to provide guidance on the measurement of antenna transmitting and receiving properties. Active Project
P187 - Standard Measurement Methods of Emissions from FM and Television Broadcast Receivers in the Frequency Range of 9 kHz to 40 GHz This standard is needed to assure consistent measurement procedures for determining Conducted and Radiated emissions in Television and FM... Active Project
P260.1 - Standard Letter Symbols for Units of Measurement (SI Units, Customary Inch-Pound Units, and Certain Other Units) The existing standard on unit symbols has been updated to conform to current international standard practices. An informative annex has been... Active Project
P269 - Measuring Electroacoustic Performance of Communication Devices The purpose of this standard is to provide laboratory test methods for evaluating the electroacoustic performance of communication devices. Active Project
P303 - Recommended Practice for Auxiliary Devices for Rotating Electrical Machines in Class I, Division 2 and Zone 2 Locations and Class II, Division 2 and Zone 22 Locations The following information is intended to bring together a brief description of basic electrical practices with regard to the application and... Active Project
P336 - Recommended Practice for Installation, Inspection, and Testing for Class 1E Power, Instrumentation, and Control Equipment at Nuclear Facilities The purpose of this recommended practice is to identify the activities, instructions, and attributes that should be considered in the process of... Active Project
P378 - Recommended Practices for Scattering Parameter Measurements Using Vector Network Analyzers Provide definitions of terms commonly used by users and manufacturers of vector network analyzers. Define and describe measurement techniques,... Active Project
P387 - Standard Criteria for Diesel-Generator Units Applied as Standby Power Supplies for Nuclear Power Generating Stations This standard provides the principal design criteria, the design features, testing, and qualification requirements for the individual diesel... Active Project
P400.3 - Guide for Partial Discharge Field Diagnostic Testing of Shielded Power Cable Systems This guide describes diagnostic methods capable of detecting and locating partial discharges from defects and damage in installed shielded power... Active Project
P421.5 - Recommended Practice for Excitation System Models for Power System Stability Studies Many of those who perform power system simulations require the complete and accurate representation of the particular excitation systems which are... Active Project
P430 - Draft Standard Procedures for the Measurement of Radio Noise from Overhead Power Lines and Substations This standard establishes uniform procedures for the measurement of radio noise generated by corona from overhead power lines and substations.... Active Project
P433 - Recommended Practice for Insulation Testing of AC Electric Machinery with High Voltage Rating up to 30 kV at Very Low Frequency The purpose of this recommended practice is as follows: a) To provide a uniform procedure for testing the stator (armature) insulation of ac... Active Project
P442 - Guide for Soil Thermal Resistivity Measurement The purpose of this guide is to provide sufficient information to enable the user to select useful commercial test equipment, or to manufacture... Active Project
P450 - Recommended Practice for Maintenance, Testing, and Replacement of Vented Lead-Acid Batteries for Stationary Applications The purpose of this recommended practice is to provide the user with information and recommendations concerning the maintenance, testing, and... Active Project
P484 - Draft Recommended Practice for Installation Design and Installation of Vented Lead-Acid Batteries for Stationary Applications Recommended design practices and procedures for storage, location, mounting, ventilation, instrumentation, pre-assembly, assembly, and charging of... Active Project
P485 - Recommended Practice for Sizing Lead-Acid Batteries for Stationary Applications Methods for defining the direct current (dc) load and for sizing a lead-acid battery to supply that load for stationary battery applications in... Active Project
P515 - the Testing, Design, Installation, and Maintenance of Electrical Resistance Trace Heating for Industrial Applications The provisions of this standard should ensure that process, fluid, or material temperatures are maintained and provide electrical, thermal, and... Active Project
P532 - Guide for Selecting and Testing Jackets for Power, Instrumentation, and Control Cables The guide provides cable users assistance in the selection of jackets for the purpose of optimizing cable design and performance. A secondary... Active Project
P563 - Guide on Conductor Self-Damping Measurements This Guide provides proven methods for investigators to perform measurements of the inherent damping characteristics of conductors. It defines... Active Project
P605 - Guide for Bus Design in Air Insulated Substations Substation rigid and strain bus structure design involves electrical, mechanical, and structural considerations. It is the purpose of this guide... Active Project
P644 - Standard Procedures for Measurement of Power Frequency Electric and Magnetic Fields from AC Power Lines The purpose of this standard is to establish uniform procedures for the measurement of electric and magnetic field levels from overhead ac power... Active Project
P656 - the Measurement of Audible Noise from Overhead Transmission Lines The purpose of this standard is to establish uniform procedures for the measurement of audible noise from overhead transmission lines, using... Active Project
P664 - Guide for Laboratory Measurement of the Power Dissipation Characteristics of Aeolian Vibration Dampers for Single Conductors This guide describes the current methodologies, including apparatus, procedures, and measurement accuracies, for the testing of vibration dampers.... Active Project
P666 - Design Guide for Electric Power Service Systems for Generating Stations While this design guide applies to all types of power generating stations, it is particularly applicable to stations in which the electric power... Active Project
P693 - Draft Recommended Practice for Seismic Design of Substations This recommended practice is for new substations and planned additions or improvements to existing substations. It is not intended that existing... Active Project
P762 - Standard Definitions for Use in Reporting Electric Generating Unit Reliability, Availability, and Productivity This standard is intended to aid the electric power industry in reporting and evaluating electric generating unit reliability, availability, and... Active Project
P802.15.4r - Part 15.4: Low-Rate Wireless Personal Area Networks (LR-WPANs) Amendment for Radio based Distance Measurement Techniques This standard defines the physical layer (PHY) and medium access control (MAC) sublayer specifications for low data rate (typically less than... Active Project
P802.15.4s - Low-Rate Wireless Networks: Amendment Enabling Spectrum Resource Measurement Capability The standard provides for ultra low complexity, ultra low cost, ultra low power consumption, and low data rate wireless connectivity among... Active Project
P802c - Overview and Architecture Amendment: Local Medium Accesss Control (MAC) Address Usage This standard serves as the foundation for the family of IEEE 802 standards published by IEEE for local area networks (LANs), metropolitan area... Active Project
P802d - Draft Overview and Architecture- Amendment: Allocation of Uniform Resource Name (URN) values in IEEE 802 standards This amendment to IEEE Std 802-2014 describes how URN values are allocated in IEEE 802(TM) standards. Active Project
Displaying results 1 - 40 of 156 - all