Digitizer Enter ModelName Here Enter ModelName Here Enter ModelName Here Enter ModelName Here Enter ModelName Here Enter ModelName Here Operating Humidity in percent Operating Shock limit in G's Operating Temperature in degrees Celsius Storage and Transport humidity in percent Storage and Transport Shock limit in G's Storage and Transport temperature in degrees Celsius Power line frequency in Hertz AC Line Voltage Power Line Current in Amps AC Power input Power line frequency in Hertz AC Line Voltage Power Line Current in Amps AC Power input E.1.1 Input channel requirements E.1.1.1 Input settings (Channel 1-N) E.1.1.1.1 User selectable analog filter Type of filter Bessel Chebyshev Gaussian Butterworth Elliptical Note that this template, as written, supports only a single filter type. If the filter type can be changed by the user then the instrument description should be modified accordingly. number of poles cut-off frequency E.1.1.1.2 Anti-Alias filter bypass selection E.1.1.1.3 Coupling AC DC GND E.1.1.1.4 Input impedance E.1.1.1.5 Full scale input This group of specifications is designed to allow full-scale range information to be entered for each possible value of input impedance. There is a single specification in the template for each value of impedance. Each specification allows for three different ranges. More values may be added or deleted as needed. Available Full Scale Input settings at 50 Ohm input impedance Input impedance set to 50 ohms Available Full Scale Input settings at 1 MOhm input impedance Input impedance set to 1MOhm E.1.1.1.6 Vertical offset range E.1.1.2 Input parameters E.1.1.2.1 Bandwidth (-3dB) E.1.1.2.2 Bandwidth (-1dB) E.1.1.2.3 Input filter bandwidth (-3dB) E.1.1.2.4 Input Filter Bandwidth (-1dB) E.1.1.2.5 Frequency response (plot) IEEE P1057/D7.4 Subclause 10.1: with data plotted. E.1.1.2.5 Plot 1) Plots are the recommended means of reporting the influence that different settings, or operating modes have on the frequency response, of the SI digitizer. 2) Frequency response plots are normally reported as typical. E.1.1.2.6 Phase linearity/group delay E.1.1.2.7 Input impedance E.1.1.2.8 Rise and fall time Rise Time Fall Time E.1.1.2.9 Absolute maximum input Absolute maximum input Sample #1: Enter conditions for impedance, maximum full scale range and coupling setting here Absolute maximum input Sample #2: Enter conditions for impedance, maximum full scale range and coupling setting here E.1.1.2.10 Crosstalk Crosstalk Low Frequency (Enter actual frequency here) Crosstalk Medium Frequency (Enter actual frequency here) Crosstalk High Frequency (Enter actual frequency here) E.1.1.2.11 Vertical offset resolution (Settability) Vertical Offset Resolution at range #1 Example 1: Enter full scale range value here Vertical Offset Resolution at range #2 Example 2: Enter full scale range value here E.1.1.2.12 VSWR VSWR is to be specified at multiple conditions of the manufacturer's choice. This template lists sample VSWR values for two bands. More (and/or different) conditions should be added as necessary. A plot may also be optionally supplied. This template does not include a sample plot. VSWR in Band #1 Example 1: Enter frequency values here VSWR in Band #2 Example 2: Enter frequency values here E.1.1.2.13 ADC resolution For ADC resolutions that vary, enter the conditions here E.1.1.2.14 DC gain accuracy E.1.1.2.15 DC gain accuracy temperature coefficient E.1.1.2.16 DC offset error E.1.1.2.17 DC offset error temperature coefficient E.1.1.2.18 AC gain accuracy E.1.1.2.19 AC gain accuracy temperature coefficient E.1.1.2.20 Differential nonlinearity (DNL) E.1.1.2.21 Integral nonlinearity (INL) E.1.1.2.22 Signal to noise and distortion (SiNAD) SINAD at low frequency Low Frequency (Enter actual frequency here) SINAD at medium frequency Medium Frequency (Enter actual frequency here) SINAD at high frequency High Frequency (Enter actual frequency here) E.1.1.2.23 Effective number of bits (ENOB) ENOB at low frequency Low Frequency (Enter actual frequency here) ENOB at medium frequency Medium Frequency (Enter actual frequency here) ENOB at high w frequency High Frequency (Enter actual frequency here) E.1.1.2.24 Signal to noise ratio (SNR) E.1.1.2.25 Total harmonic distortion (THD) E.1.1.2.26 Spurious free dynamic range (SFDR) E.1.1.2.27 Inter-modulation distortion (IMD) E.1.1.2.28 Probe and probe compensation E.1.1.2.29 RMS noise (terminated with no input) E.1.2 Output requirements None E.1.3 Time base requirements E.1.3.1 Time base programmable settings E.1.3.1.1 Reference selection Internal External E.1.3.1.2 Time base selection Internal External E.1.3.1.3 Sample clock rate E.1.3.2 General time base parameters E.1.3.2.1 Sample clock range E.1.3.2.2 Sample clock resolution E.1.3.2.3 Sample clock frequency accuracy E.1.3.2.4 Reference long term drift E.1.3.2.5 Sampling jitter E.1.3.2.6 Trigger time resolution E.1.3.2.7 Trigger time jitter E.1.3.3 Time base input port parameters E.1.3.3 Time base input port parameters E.1.3.3.1 Port type (Fref_in) See Ports Section E.1.3.3.3 Signal type (Fref-in) Enter description here E.1.3.3.5 Duty cycle tolerance E.1.3.3.6 Threshold adjustment range E.1.3.3.7 Input frequency range E.1.3.3.8 Input impedance E.1.3.3.9 Coupling (if applicable to signal type) AC DC E.1.3.3.10 Minimum slew rate (for non sinusoidal input types) E.1.3.3.11 Input amplitude range E.1.3.3.12 Absolute maximum input E.1.3.3 Time base input port parameters E.1.3.3.2 Port type (Clk_in) See Ports Section E.1.3.3.4 Signal type (Clk-in) Enter description here E.1.3.3.5 Duty cycle tolerance E.1.3.3.6 Threshold adjustment range E.1.3.3.7 Input frequency range E.1.3.3.8 Input impedance E.1.3.3.9 Coupling (if applicable to signal type) AC DC E.1.3.3.10 Minimum slew rate (for non sinusoidal input types) E.1.3.3.11 Input amplitude range E.1.3.3.12 Absolute maximum input E.1.3.4 Time base output port parameters E.1.3.4 Time base output port parameters E.1.3.4.1 Port type (Fref_out) See Ports Section E.1.3.4.3 Signal type Describe the expected signal type here E.1.3.4.4 Output amplitude E.1.3.4.5 Offset adjustment range (if applicable to signal type) E.1.3.4.6 Output impedance E.1.3.4.7 Output frequency range E.1.3.4.8 Output clock jitter E.1.3.4.9 Output circuit protection Enter description here E.1.3.4 Time base output port parameters E.1.3.4.2 Port type (Clk_out) See Ports Section E.1.3.4.3 Signal type Describe the expected signal type here E.1.3.4.4 Output amplitude E.1.3.4.5 Offset adjustment range (if applicable to signal type) E.1.3.4.6 Output impedance E.1.3.4.7 Output frequency range E.1.3.4.8 Output clock jitter E.1.3.4.9 Output circuit protection Enter description here E.1.4 Power requirements See PowerRequirements Section E.1.5 Physical characteristics See PhysicalCharacteristics Section E.1.6 Communications and control requirements E.1.6.1 Controllability/software driver See Control Section E.1.6.2 Internal/external control Specify whether can be controlled via an external or internal controller, or both E.1.6.3 Trigger port(s) requirements E.1.6.3.1 Trigger programmable settings E.1.6.3.1.1 Trigger type Edge Software E.1.6.3.1.2 Coupling AC DC GND E.1.6.3.1.3 Polarity/slope plus minus E.1.6.3.1.4 Input impedance E.1.6.3.1.5 Threshold adjustment (if applicable) E.1.6.3.1.6 Holdoff E.1.6.3.1.7 Hysteresis characteristics E.1.6.3.1.8 Source Internal External Software E.1.6.3.2 Trigger input parameters (Tsync_in and Ch 1-N) E.1.6.3.2.1 Trigger level range E.1.6.3.2.2 Trigger sensitivity E.1.6.3.2.3 Trigger bandwidth E.1.6.3.2.4 Threshold adjustment range E.1.6.3.2.5 Trigger level resolution E.1.6.3.2.6 Hysteresis E.1.6.3.2.7 Absolute maximum input E.1.6.3.2.8 Re-arm time E.1.6.3.2.9 Input impedance E.1.6.3.2.10 Trigger hold off range E.1.6.3.2.11 Trigger delay range E.1.6.3.2.12 Trigger delay resolution E.1.6.3.3 Trigger output parameters (Tsync_out) E.1.6.3.3.1 Port type (Tsync_out) See Ports Section E.1.6.3.3.2 Signal type 1) Describe the signal type in conventional terms meaningful to the user. 2) There may be multiple signal types supported. If so, define the applicable setting. E.1.6.3.3.3 Amplitude range E.1.6.3.3.4 Amplitude resolution 1) If the trigger output has adjustable amplitude. 2) Spell it out in terms of range and adjustment resolution. E.1.6.3.3.5 Trigger output offset range E.1.6.3.3.6 Trigger output offset resolution E.1.6.3.3.7 Trigger output delay E.1.6.3.3.8 Trigger output impedance E.1.6.3.4 Memory parameters E.1.6.3.4.1 Memory type 1) Volatile or non-volatile memory. 2) Describe any limitations to its use. E.1.6.3.4.2 Total waveform memory size E.1.6.3.4.3 Number of memory segments E.1.6.3.4.4 Segment size range E.1.6.3.4.5 Security declassification 1) Declassification only applies to memory the user can write too. E.1.6.4 High Speed Data Port None E.1.6.5 Physical layer None