Standard Icon

Power and Energy Standards

Displaying results 641 - 680 of 1294
Standard Name
Status Help less all
1416-1998 - Recommended Practice for the Interface of New Gas-Insulated Equipment in Existing Gas-Insulated SubstationsRecommendations for the connection of a gas-insulated substation to another gas-insulated substation of a different make are given. Active Standard
1425-2001 - Guide for the Evaluation of the Remaining Life of Impregnated Paper-Insulated Transmission Cable SystemsThis guide provides technical information regarding factors that can affect the life of an impregnated paper-insulated transmission cable system,... Active Standard
1427-2006 - Guide for Recommended Electrical Clearances and Insulation Levels in Air Insulated Electrical Power SubstationsThis guide, covering three-phase ac systems from 1 kV to 800 kV, provides recommended electrical operating and safety clearances and insulation... Active Standard
1428-2004 - Guide for Installation Methods for Fiber Optic Cables in Electric Power Generating Stations and in Industrial FacilitiesThis guide is intended for cables designed for use in power generating stations and industrial facilities, in both the outside plant environment... Active Standard
1434-2000 - Guide to the Measurement of Partial Discharges in Rotating MachineryA review of the nature of partial discharge in machine windings, how it can be measured under both off-line and on-line conditions, how it can be... Superseded Standard
1434-2014 - Approved Draft Guide for the Measurement of Partial Discharges in AC Electric MachineryA review of the nature of partial discharge in machine windings, how it can be measured under both off-line and on-line conditions, how it can be... Active Standard
1441-2004 - Guide for Inspection of Overhead Transmission Line ConstructionVarious approaches to good inspection practices for the construction of overhead transmission lines are covered in this guide. Inspection... Withdrawn Standard
1453-2004 - Recommended Practice for Measurement and Limits of Voltage Fluctuations and Associated Light Flicker on AC Power SystemsVoltage fluctuations on electric power systems sometimes give rise to noticeable illumination changes from lighting equipment. This phenomenon is... Withdrawn Standard
1453-2011 - Recommended Practice--Adoption of IEC 61000-4-15:2010, Electromagnetic compatibility (EMC)--Testing and measurement techniques--Flickermeter--Functional and design specificationsIEC 61000-4-15:2010 is adopted by this standard. IEC 61000-4-15:2010 gives a functional and design specification for flicker measuring apparatus... Active Standard
1453.1-2012 - Guide--Adoption of IEC/TR 61000-3-7:2008, Electromagnetic compatibility (EMC)--Limits--Assessment of emission limits for the connection of fluctuating installations to MV, HV and EHV power systemsIEC/TR 61000-3-7:2008 is adopted by this guide. IEC 61000-3-7:2008 provides guidance on the principles that can be used as the basis for... Active Standard
1459-2000 - Standard Definitions for the Measurement of Electric Power Quantities under Sinusoidal, Non-Sinusoidal, Balanced, or Unbalanced ConditionsThis is a trial-use standard for definitions used for measurement of electric power quantities under sinusoidal, nonsinusoidal, balanced, or... Superseded Standard
1459-2010 - Standard Definitions for the Measurement of Electric Power Quantities Under Sinusoidal, Nonsinusoidal, Balanced, or Unbalanced ConditionsThis document provides definitions of electric power to quantify the flow of electrical energy in single-phase and three-phase circuits under... Active Standard
1491-2005 - Guide for Selection and Use of Battery Monitoring Equipment in Stationary ApplicationsMonitoring and measurement of battery parameters is an important element of maintaining a fully operational battery system. This guide presents... Superseded Standard
1491-2012 - Guide for Selection and Use of Battery Monitoring Equipment in Stationary ApplicationsOperational parameters that may be observed by battery monitoring equipment used in stationary applications and the relative value of such... Active Standard
1493-2006 - Guide for the Evaluation of Solvents Used for Cleaning Electrical Cables and AccessoriesTest procedures for evaluating the physical characteristics of cable cleaning solvents and their compatibility with extruded dielectric cable... Active Standard
1511-2004 - Guide for Investigating and Analyzing Power Cable, Joint, and Termination Failures on Systems Rated 5 kV Through 46 kVThis guide applies to the process of investigating, evaluating, and analyzing field failures. This guide covers the overall format for failure... Active Standard
1511.1-2010 - Guide for Investigating and Analyzing Shielded Power Cable Failures on Systems Rated 5 kV Through 46 kVThis guide covers specific methods of failure mode classifications and analysis for shielded power cables rated 5 kV through 46 kV. Active Standard
1513-2001 - Recommended Practice for Qualification of Concentrator Photovoltaic (PV) Receiver Sections and ModulesThe minimum tests and inspections required to evaluate photovoltaic concentrating modules, and a common approach (e.g., between producer and... Withdrawn Standard
1515-2000 - Recommended Practice for Electronic Power Subsystems: Parameter Definitions, Test Conditions, and Test MethodsThis recommended practice defines many common parameters for AC-DC and DC-DC electronic power distribution components and subsystems. This enables... Active Standard
1523-2002 - Guide for the Application, Maintenance, and Evaluation of Room Temperature Vulcanizing (RTV) Silicone Rubber Coatings for Outdoor Ceramic InsulatorsVarious important aspects that are needed for satisfactory long-term performance of high-voltage insulator coatings (HVIC) are presented in this... Active Standard
1526-2003 - Recommended Practice for Testing the Performance of Stand-Alone Photovoltaic SystemsTests to determine the performance of stand-alone photovoltaic (PV) systems and for verifying PV system design are presented in this recommended... Active Standard
1527-2006 - Recommended Practice for the Design of Flexible Buswork Located in Seismically Active AreasThe engineering and design of flexible bus connections for bus and equipment in electric power substations is described. This recommended practice... Active Standard
1531-2003 - Guide for Application and Specification of Harmonic FiltersGuidelines for specification of components, protection, and control of harmonic filters are provided. This guide applies to the use of 50 Hz and... Active Standard
1534-2002 - Recommended Practice for Specifying Thyristor-Controlled Series CapacitorsRecommended practices for specifying Thyristor-Controlled Series Capacitor (TCSC) installations used in series with transmission lines are... Withdrawn Standard
1534-2009 - Recommended Practice for Specifying Thyristor-Controlled Series CapacitorsRecommended practices for specifying Thyristor-Controlled Series Capacitor (TCSC) installations used in series with transmission lines are... Active Standard
1538-2000 - Guide for Determination of Maximum Winding Temperature Rise in Liquid-Filled TransformersProvides guidance for determining the hottest-spot temperature in distribution and power transformers built in accordance with IEEE Std C57.12.00... Active Standard
1542-2007 - Guide for Installation, Maintenance, and Operation of Irrigation Equipment Located Near or Under Power LinesThe guide is based on industry practices, and guidelines for installation, maintenance and operation of irrigation equipment near or under power... Active Standard
1547-2003 - Interconnecting Distributed Resources with Electric Power SystemsThis standard is the first in the 1547 series of interconnection standards and is a benchmark milestone demonstrating the open consensus process... Active Standard
1547.1-2005 - Standard Conformance Test Procedures for Equipment Interconnecting Distributed Resources with Electric Power SystemsThis standard specifies the type, production, and commissioning tests that shall be performed to demonstrate that the interconnection functions... Active Standard
1547.2-2008 - Application Guide for IEEE Std 1547(TM), Interconnecting Distributed Resources with Electric Power SystemsIn this paper, technical background and application details to support understanding of IEEE Std 1547-2003 are provided. The guide facilitates the... Active Standard
1547.3-2007 - Guide for Monitoring, Information Exchange, and Control of Distributed Resources Interconnected with Electric Power SystemsThis guide is intended to facilitate the interoperability of distributed resources (DR) and help DR project stakeholders implement monitoring,... Active Standard
1549-2011 - Microwave Filter DefinitionsStandardized definition of terms commonly in the field of electrical networks and filters. Active Standard
1553-2002 - Voltage Endurance Testing of Form-Wound Coils and Bars for HydrogeneratorsThe test parameters and acceptance criteria for voltage-endurance testing of form-wound bars and coils for use in large hydrogenerators are... Active Standard
1561-2007 - Guide for Optimizing the Performance and Life of Lead-Acid Batteries in Remote Hybrid Power SystemsThis guide is applicable to lead-acid batteries that are used as the energy storage component in remote hybrid power supplies. The remote hybrid... Active Standard
1562-2007 - Guide for Array and Battery Sizing in Stand-Alone Photovoltaic (PV) SystemsA method for properly sizing the PV array and battery for stand-alone PV systems where PV is the only charging source is recommended (in... Active Standard
1564-2014 - Guide for Voltage Sag IndicesAppropriate voltage sag indices and characteristics of electrical power and supply systems as well as the methods for calculating them are... Active Standard
1572-2004 - Guide for Application of Composite Line Post InsulatorsThis is a guide for the application of composite post insulators to overhead transmission and distribution lines. It is based on utility field... Withdrawn Standard
1573-2003 - Recommended Practice for Electronic Power Subsystems: Parameters, Interfaces, Elements, and PerformanceA technical basis for implementation of electronic power subsystems is provided in this recommended practice. It is intended for electronic... Active Standard
1578-2007 - Recommended Practice for Stationary Battery Electrolyte Spill Containment and ManagementDescriptions of products, methods, and procedures relating to stationary batteries, battery electrolyte spill mechanisms, electrolyte containment... Active Standard
1585-2002 - Guide for the Functional Specification of Medium Voltage (1- 35kV) Electronic Series Devices for Compensation of Voltage FluctuationsAn approach to prepare a specification for an electronic device connected in series to compensate voltage fluctuations is presented. This guide... Active Standard