Standard Icon

Power and Energy Standards

Displaying results 441 - 480 of 1454
Standard Name
Status Help less all
805-1984 - Recommended Practice for System Identification in Nuclear Power Plants and Related FacilitiesThis recommended practice provides a single source of nuclear power plant system descriptions that, along with related recommended practices... Withdrawn Standard
806-1986 - Recommended Practice for System Identification in Fossil-Fueled Power Plants and Related FacilitiesTo aid identification of components and systems in fossil-fueled power plants and related facilities descriptions of systems, structures and... Withdrawn Standard
807-2011 - Recommended Practice for Unique Identification in Hydroelectric FacilitiesA unique identification system for hydroelectric facilities that segregates and incorporates plant, unit, system, and component identifiers as a... Active Standard
810-1987 - Hydraulic Turbine and Generator Integrally Forged Shaft Couplings and Shaft Runout TolerancesThis standard applies to the dimensions of integrally forged shaft couplings and to the shaft runout tolerances. Shafts and couplings included in... Superseded Standard
810-2015 - Hydraulic Turbine and Generator Shaft Couplings and Shaft Runout TolerancesThe dimensions for all types of shaft couplings and shaft runout tolerances for hydraulic turbines and generators are included in this standard.... Active Standard
812-1984 - Standard Definitions of Terms Relating to Fiber OpticsThis document is based on the NTIA-SP-794 Optical Waveguide Communications Glossary, issued in September 1979 by the U.S. Department of Commerce; Withdrawn Standard
816-1987 - Guide for Determining the Smoke Generation of Solid Materials Ued for Insulations and Coverings of Electric Wire and CableThe guide is to aid wire and cable manufacturers in the study of smoke generation characteristics of materials used in products. The two test... Withdrawn Standard
817-1993 - Standard Test Procedure for Flame-Retardant Coatings Applied to Insulated Cables in Cable TraysA test protocol and the performance criteria to determine the flame propagation tendency of flame-retardant coated cables in a vertical cable tray... Withdrawn Standard
820-2006 - Standard Telephone Loop Performance CharacteristicsCommon denominators for subscriber line performance, independent of facility types, construction processes or equipment, and circuit provisioning... Active Standard
824-1985 - Series Capacitors in Power SystemsThis standard applies to capacitors and assemblies of capacitors, insulation means, switching and protective equipment, and control accessories... Superseded Standard
824-1994 - Series Capacitors in Power SystemsCapacitors and assemblies of capacitors, insulation means, switching, protective equipment, and control accessories that form a complete bank for... Superseded Standard
824-2005 - Series Capacitor Banks in Power SystemsThis standard represents a significant update to IEEE 824-1994. Series capacitor bank component and bank duty cycle ratings, equipment insulation... Active Standard
833-1988 - Recommended Practice for the Protection of Electric Equipment in Nuclear Power Generating Stations from Water HazardsPresents recommended practices for providing the electric systems and equipment in nuclear power plants with protection from water hazards. The... Superseded Standard
833-2005 - Recommended Practice for the Protection of Electric Equipment in Nuclear Power Generating Stations from Water HazardsGuidance regarding protection of electrical equipment from sources of water directed onto or around electrical equipment is provided. Active Standard
835-1994 - Standard Power Cable Ampacity TablesOver 3000 ampacity tables for extruded dielectric power cables rated through 138 kV and laminar dielectric power cables rated through 500 kV are... Active Standard
835a-2012 - Standard Power Cable Ampacity Tables Amendment 1: Revision to IntroductionCorrections to the introduction for the standard with over 3000 ampacity tables for extruded dielectric power cables rated through 138 kV and... Active Standard
837-1989 - Qualifying Permanent Connections Used in Substation GroundingThis IEEE standard has been written to fill a need for standardization of terminology and test requirements for permanent grounding connections... Superseded Standard
837-2002 - Qualifying Permanent Connections Used in Substation GroundingDirection and methods for qualifying permanent connections used for substation grounding are provided in this standard. This standard particularly... Superseded Standard
837-2014 - Qualifying Permanent Connections Used in Substation GroundingDirection and methods for qualifying permanent connections used for substation grounding are provided in this standard. This standard particularly... Active Standard
845-1988 - Guide to Evaluation Man-Machine Performance in Nuclear Power Generating Station Control Rooms and Other PeripheriesThe purpose of this guide is to provide guidance for the selection and application of human factors techniques to carry out the following tasks in... Superseded Standard
845-1999 - Guide for the Evaluation of Human-System Performance in Nuclear Power Generating StationsGuidance for evaluating human-system performance related to systems, equipment, and facilities in nuclear power generating stations is provided.... Active Standard
848-1996 - Standard Procedure for the Determination of the Ampacity Derating of Fire-Protected CablesA detailed test procedure is provided for determining the ampacity or derating factor in the following cable installation configurations: block... Superseded Standard
848-2015 - Standard Procedure for the Determination of the Ampacity Derating Factor for Fire-Protected Cable SystemsA detailed test procedure is provided for determining the ampacity derating factor in the following cable installation configurations: block-out... Active Standard
853-1985 - Recommended Practice for Voltage-Endurance Testing of Enameled WireThe scope of this recommended practice covers the application of center grounded applied voltage but not voltage wave shapes in which either the... Withdrawn Standard
857-1990 - Guide for Test Procedures for HVDC Thyristor ValvesThis guide contains information and recommendations for the type testing of thyristor valves for high-voltage direct-current (HVDC) power... Superseded Standard
857-1996 - Recommended Practice for Test Procedures for High-Voltage Direct-Current Thyristor ValvesInformation and recommendations for the type testing of thyristor valves for high-voltage direct-current (HVDC) power transmission systems are... Withdrawn Standard
858-1987 - Standard Definitions in Power Operations TerminologyThis standard is a revision of Part 1 of IEEE Std. 346-1973, Glossary of Power Operations Terms. It is intended for engineers in power systems... Superseded Standard
858-1993 - Standard Definitions in Power Operations TerminologyTerms in the field of power operations are defined. Power distribution and transmission aspects are covered. Withdrawn Standard
859-1987 - Standard Terms for Reporting and Analyzing Outage Occurrences and Outage States of Electrical Transmission FacilitiesThe report is intended to aid the electric power industry in reporting and analyzing outrage occurrences of transmission facilities. Use of... Active Standard
928-1986 - Recommended Criteria for Terrestrial Photovoltaic Power SystemsThe purpose is to establish the general performance criteria for terrestrial photovoltaic power systems and to provide an overall framework for... Withdrawn Standard
929-1988 - Recommended Practice for Utility Interface of Residential and Intermediate Photovoltaic (PV) SystemsThis recommended practice applies to utility interconnected residential and intermediate size photovoltaic power systems capable of two-way energy... Superseded Standard
929-2000 - Recommended Practice for Utility Interface of Photovoltaic (PV) SystemsThis recommended practice contains guidance regarding equipment and functions necessary to ensure compatible operation of photovoltaic (PV)... Withdrawn Standard
930-1987 - Guide for the Statistical Analysis of Electrical Insulation Voltage Endurance DataThe guide describes, with examples, statistical methods to analyze the data for time-to-failure from constant-stress voltage endurance tests or... Superseded Standard
930-2004 - (Replaced) Guide for the Statistical Analysis of Electrical Insulation Breakdown DataThis guide describes, with examples, statistical methods to analyze times to break down and breakdown voltage data obtained from electrical... Active Standard
933-1999 - Guide for the Definition of Reliability Program Plans for Nuclear Power Generating StationsGuidelines for the definition of a reliability program at nuclear power generating stations are developed. Reliability programs during the... Superseded Standard
933-2013 - Guide for the Definition of Reliability Program Plans for Nuclear Generating Stations and Other Nuclear FacilitiesGuidelines for the definition of a reliability program at nuclear generating stations and other nuclear facilities are provided. The document... Active Standard
934-1987 - Standard Requirements for Replacement Parts for Class 1E Equipment in Nuclear Power Generating StationsThe standard sets forth basic requirements for the selection and utilization of replacement parts for Class IE equipment in nuclear power... Withdrawn Standard
935-1989 - Guide on Terminology for Tools and Equipment to Be Used in Live Line WorkingThe following topics were dealt with: This standard applies to terminology for tools and equipment used in live overhead power line working. This... Active Standard
936-1987 - Guide for Self-Commutated ConvertersThis guide applies to self-commutated electronic power converters in which commutation is accomplished by components within the converter. In... Withdrawn Standard