Standard Icon

Power and Energy Standards

Displaying results 361 - 400 of 1396
Standard Name
Status Help less all
421.5-1992 - Recommended Practice for Excitation System Models for Power System Stability StudiesExcitation system models suitable for use in large scale power system stability studies are presented. With these models, most of the excitation... Superseded Standard
421.5-2005 - Recommended Practice for Excitation System Models for Power System Stability StudiesExcitation system models suitable for use in large-scale system stability studies are presented. Important limiters and supplementary controls are... Active Standard
421A-1978 - Guide for Identification, Testing, and Evaluation of the Dynamic Performance of Excitation Control SystemsThis IEEE guide includes criteria, definitions, and test procedures for evaluating the dynamic performance of excitation control systems as... Superseded Standard
421B-1979 - High-Potential-Test Requirements for Excitation Systems for Synchronous MachinesThis standard applies to high-potential testing of complete excitation systems and their components for synchronous machines. Also included are... Superseded Standard
422-1986 - Guide for the Design and Installation of Cable Systems in Power Generating StationsThis guide provides guidance and recommended practices on the installation and maintenance of liquid-immersed power transformers rated 501 kVA and... Withdrawn Standard
428-1981 - Standard Definitions and Requirements for Thyristor AC Power ControllersThese recommendations apply to thyristor AC power controllers that are low voltage, power electronic, industrial class equipment for the control... Withdrawn Standard
429-1994 - Recommended Practice for Thermal Evaluation of Sealed Insulation Systems for AC Electric Machinery Employing Form-Wound Preinsulated Stator Coils for Machines Rated 6900 V and BelowIn this IEEE standard a test procedure for comparing two or more sealed insulation systems in accordance with their expected life at rated... Withdrawn Standard
430-1986 - Standard Procedures for the Measurement of Radio Noise from Overhead Power Lines and SubstationsThe primary purpose of this standard is to establish uniform procedures for the measurement of radio noise generated by corona from overhead power... Withdrawn Standard
432-1976 - Guide for Insulation Maintenance for Rotating Electrical Machinery (5 hp to less than 10 000 hp)This insulation maintenance guide is intended to apply in general to industrial air-cooled rotating electrical machines rated from 5 hp to 10000... Superseded Standard
432-1992 - Guide for Insulation Maintenance for Rotating Electric Machinery (5 hp to less than 10 000 hp)In this standard, information necessary to permit an effective evaluation of the insulation systems of medium and small rotating electric machines... Withdrawn Standard
433-1974 - Recommended Practice for Insulation Testing of Large AC Rotating Machinery with High Voltage at Very Low FrequencyThis document provides a uniform method of VLF testing in order to obtain consistent results, accumulate meaningful experience, and lead to... Withdrawn Standard
434-1973 - Guide for Functional Evaluation of Insulation Systems for Large High-Voltage MachinesThe purpose of this guide is to describe classification test methods which may be used to compare insulation systems in use, or proposed for use,... Superseded Standard
434-2006 - Guide for Functional Evaluation of Insulation Systems for AC Electric Machines Rated 2300 V and AboveA procedure that may be used to evaluate and compare insulation systems used, or proposed for use, in large ac electric machines is described in... Active Standard
436-1977 - Guide for Making Corona (Partial Discharge) Measurements on Electronics TransformersThis guide covers the detection of corona and the measurement of corona magnitude in electronics transformers. Test conditions, terminology, test... Superseded Standard
436-1991 - Guide for Making Corona (Partial Discharge) Measurements on Electronics TransformersA uniform procedure for making corona (partial discharge) measurements by electrical means on electronic transformers is presented. Methods of... Active Standard
442-1981 - Guide for Soil Thermal Resistivity MeasurementsThis guide covers the measurement of soil thermal resistivity. A thorough knowledge of the thermal properties of a soil will enable the user to... Active Standard
444-1973 - Standard Practices and Requirements for Thyristor Converters for Motor Drives Part 1- Converters for DC Motor Armature SuppliesThis standard applies to all types of line-commutated semiconductor power converters, employing monocrystalline semiconductor thyristors or diodes... Withdrawn Standard
446-1987 - Recommended Practice for Emergency and Standby Power Systems for Industrial and Commerical ApplicationsRecommended engineering principles, practices, and guidelines for the selection and application of emergency and standby power systems are... Superseded Standard
446-1995 - Recommended Practice for Emergency and Standby Power Systems for Industrial and Commercial ApplicationsThis Recommended Practice addresses the uses, power sources, design, and maintenance of emergency and standby power systems. Chapter 3 is a... Active Standard
449-1990 - Ferroresonant Voltage RegulatorsThis standard pertains to ferroresonant voltage regulators that operate at relatively constant frequencies and provide substantially constant... Withdrawn Standard
449-1998 - Ferroresonant Voltage RegulatorsFerroresonant transformers used as regulators in electronic power supplies and in other equipment are covered. Guides to application and test... Active Standard
450-1987 - Recommended Practice for Maintenance,Testing, and Replacement of Large Lead Batteries for Generating Stations and SubstationsThis recommended practice is limited to providing recommended practices of maintenance, test schedules, and testing procedures than can be used to... Superseded Standard
450-1995 - Recommended Practice for Maintenance, Testing, and Replacement of Vented Lead-Acid Batteries for Stationary ApplicationsMaintenance, test schedules, and testing procedures that can be used to optimize the life and performance of permanently installed, vented lead... Superseded Standard
450-2002 - Recommended Practice for Maintenance, Testing , and Replacement of Vented Lead-Acid Batteries for Stationary ApplicationsMaintenance, test schedules, and testing procedures that can be used to optimize the life and performance of permanently installed, vented lead... Superseded Standard
460-1988 - Electrical Measuring Transducer for Converting AC Electrical Quantities into DC Electrical QuantitiesThis standard applies to measuring transducers used for converting AC electrical quantities such as current, voltage, power (active or reactive),... Withdrawn Standard
463-1977 - Electrical Safety Practices in Electrolytic Cell Line Working ZonesThis standard covers means of safeguarding personnel while operating or maintaining equipment located in electrolytic cell line working zones.... Superseded Standard
463-1993 - Electrical Safety Practices in Electrolytic Cell Line Working ZonesMeans of safeguarding personnel while operating or maintaining equipment located in electrolytic cell line working zones are provided. Included... Withdrawn Standard
463-2006 - Electrical Safety Practices in Electrolytic Cell Line Working ZonesMeans for improved safeguarding of personnel while operating or maintaining equipment located in electrolytic cell line working zones are provided... Superseded Standard
467-1980 - Standard Quality Assurance Program Requirements for the Design and Manufacture of Class 1E Instrumentation and Electric Equipment for Nuclear Power Generating StationsThis standard establishes the basic Quality Assurance Program requirements to be implemented by manufacturers of Class 1E Instrumentation and... Withdrawn Standard
484-2002 - Recommended Practice for Installation Design and Installation of Vented Lead-Acid Batteries for Stationary ApplicationsRecommended design practices and procedures for storage, location, mounting, ventilation, instrumentation, preassembly, assembly, and charging of... Active Standard
484-1987 - Recommended Practice for Installation Design and Installation of Large Lead Storage Batteries for Generating Stations and SubstationsProvides recommended design practices and procedures for storage, location, mounting, ventilation, instrumentation, preassembly, assembly and... Superseded Standard
484-1996 - Recommended Practice for Installation Design and Installation of Vented Lead-Acid Batteries for Stationary ApplicationsIn this IEEE Standard recommended design practices and procedures for storage, location, mounting, ventilation, instrumentation, preassembly,... Superseded Standard
485-1983 - Recommended Practice for Sizing Large Lead Storage Batteries for Generating Stations and SubstationsMethods for defining the dc load in a generating station or a substation and for sizing a lead storage battery to supply that load are described.... Superseded Standard
485-1997 - Recommended Practice for Sizing Lead-Acid Batteries for Stationary ApplicationsMethods for defining the DC load and for sizing a lead-acid battery to supply that load for stationary battery applications in full float... Superseded Standard
485-2010 - Recommended Practice for Sizing Lead-Acid Batteries for Stationary ApplicationsMethods for defining the direct current (dc) load and for sizing a lead-acid battery to supply that load for stationary battery applications in... Active Standard
487-1980 - Guide for the Protection of Wire-Line Communication Facilities Serving Electric Power StationsWire-line communication facilities serving electric power stations often require special high-voltage protection against the effects of fault... Superseded Standard
487-1992 - Recommended Practice for the Protection of Wire-Line Communication Facilities Serving Electric Power StationsWorkable methods for protecting wire-line communication circuits entering power stations are presented. This standard covers: the electric power... Superseded Standard
487-2000 - Recommended Practice for the Protection of Wire-Line Communication Facilities Serving Electric Supply LocationsWorkable methods for protecting wire-line communication circuits entering electric supply locations are presented. This document covers: the... Superseded Standard
487-2007 - Recommended Practice for the Protection of Wire-Line Communication Facilities Serving Electric Supply LocationsWorkable methods for protecting wire-line communication circuits entering electric supply locations are presented. This document covers: the... Active Standard