Standard Icon

Instrumentation and Measurement Standards

Displaying results 321 - 360 of 685
Standard Name
Status Help less all
1174-2000 - Standard Serial Interface for Programmable InstrumentationA serial, full-duplex, asynchronous, 9-pin data terminal equipment (DT ) communications port for programmable instrumentation that follows ANSI... Active Standard
1177-1993 - FASTBUS Standard Routines1177-1993 Abstract: Standard software routines for use with the system in IEEE Std 960-1993 are defined. 960-1993 Abstract: Mechanical, signal,... Superseded Standard
1181-1991 - Recommended Practice for Latchup Test Methods for CMOS and BiCMOS Integrated- Circuit Process CharacterizationRecommendations are provided for the layout and test methods required to characterize properly latchup behavior in CMOS and BiCMOS integrated... Withdrawn Standard
1188-1996 - Recommended Practice for Maintenance, Testing, and Replacement of Valve- Regulated Lead-Acid (VRLA) Batteries for Stationary ApplicationsIn this IEEE standard maintenance, test schedules, and testing procedures that can be used to optimize the life and performance of valve-regulated... Superseded Standard
1188-2005 - Recommended Practice for Maintenance, Testing, and Replacement of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary ApplicationsThis recommended practice is limited to maintenance, test schedules, and testing procedures that can be used to optimize the life and performance... Active Standard
1188a-2014 - Recommended Practice for Maintenance, Testing, and Replacement of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary Applications - Amendment 1: Updated VRLA Maintenance ConsiderationsNew guidance to users dealing with premature capacity failures with VRLA batteries and updated definitions are addressed in this amendment. Active Standard
1193-1994 - Guide for Measurement of Environmental Sensitivities of Standard Frequency GeneratorsStandard frequency generators that include all atomic frequency standards and precision quartz crystal oscillators are addressed. There are three... Superseded Standard
1193-2003 - Guide for Measurement of Environmental Sensitivities of Standard Frequency GeneratorsStandard frequency generators that include all atomic frequency standards, quartz oscillators, dielectric resonator oscillators, yttrium-iron... Active Standard
1202-1991 - Flame Testing of Cables for Use in Cable Tray in Industrial and Commercial OccupanciesA test protocol and the performance criteria to determine the flame propagation tendency of cables in a vertical cable tray are presented. They... Superseded Standard
1202-2006 - Flame-Propagation Testing of Wire & CableStandardization of cable flame propagation testing is beneficial to cable manufacturers, distributors, and users. Uniform procedures; consistent,... Active Standard
1202-2006/Cor 1-2012 - Flame-Propagation Testing of Wire and Cable - Corrigendum 1Corrected English unit conversions are included in this corrigendum to IEEE Std 1202-2006. Active Standard
1210-1996 - Standard Tests for Determining Compatibility of Cable-Pulling Lubricants With Wire and CableCriteria and test methods for determining the compatibility of cable-pulling lubricants (compounds) with cable jacket or other exterior cable... Superseded Standard
1210-2004/Cor 1-2014 - Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable - Corrigendum 1Criteria and test methods for determining the compatibility of cable-pulling lubricants (compounds) with cable jacket or other exterior cable... Active Standard
1210-2005 - Standard Tests for Determining Compatibility of Cable-Pulling Lubricants With Wire and CableCriteria and test methods for determining the compatibility of cable-pulling lubricants (compounds) with cable jacket or other exterior cable... Active Standard
1214-1992 - Standard Multichannel Analyzer (MCA) Histogram Data Interchange Format for Nuclear SpectroscopyA standard format for data interchange used to transfer multichannel pulse height data on magnetic media between laboratories is provided. The... Active Standard
1222-2003 - All-Dielectric Self-Supporting Fiber Optic CableSUMMARY: This standard covers construction, mechanical, electrical, and optical performance, installation guidelines, acceptance criteria, test... Superseded Standard
1222-2011 - Testing and Performance for All-Dielectric Self-Supporting (ADSS) Fiber Optic Cable for Use on Electric Utility Power LinesThis standard covers the construction, mechanical, electrical and optical performance, installation guidelines, acceptance criteria, test... Active Standard
1226-1993 - ABBET(TM) Trial-Use A Broad-Based Environment for Test (ABBET) Overview and ArchitectureThe overall concept of A Broad-Based Environment for Test (ABBET) is defined, and mandatory requirements for implementations ABBET are specified.... Superseded Standard
1226-1998 - a Broad-Based Environment for Test (ABBET(TM)), Overview and ArchitectureThe overall concept of A Broad-Based Environment for Test (ABBET)/sup TM/ is defined, and mandatory requirements for implementation of ABBET are... Withdrawn Standard
1226.1-1993 - ABBET(TM) Trial-Use Common Ada Packages for A Broad-Based Environment for Test (ABBET(TM))Withdrawn Standard. Withdrawn Date: Mar 19, 1998. No longer endorsed by the IEEE. Ada packages that specify general purpose test support data... Withdrawn Standard
1226.2-1993 - ABBET(TM) Trial-Use Ada-Based ATLAS-Level Test Procedure Interface for A Broad-Based Environment for Test (ABBET(TM))Ada packages that specify data types and services for the Ada-based ATLAS-level test procedure interface for a broad-based environment for test ... Withdrawn Standard
1226.3-1998 - Software Interface for Resource Management for a Broad Based Environment for Test (ABBET(TM))The services needed to access and manage descriptive information about resources in an automatic test system (ATS) are covered. This information... Withdrawn Standard
1226.6-1996 - ABBET(TM) Guide for the Understanding of the "A Broad Based Environment for Test (ABBET)(TM)" StandardAs a part of the family of IEEE ABBET/sup TM/ standards, this guide facilitates an understanding of the relationships of IEEE ABBET 1226-1993 and... Withdrawn Standard
1232-1995 - Artificial Intelligence and Expert System Tie to Automatic Test Equipment (AI-ESTATE): Overview and ArchitectureThe report is the base standard for the AI-ESTATE set of standards. The overall concept of AI-ESTATE, which is a set of specifications for data... Superseded Standard
1232-2002 - (Replaced) Artificial Intelligence Exchange and Service Tie to All Test Environments (AI- ESTATE)AI-ESTATE is a set of specifications for data interchange and for standard services for the test and diagnostic environment. The purpose of AI... Superseded Standard
1232-2010 - Artificial Intelligence Exchange and Service Tie to All Test Environments (AI-ESTATE)Data interchange and standard software services for test and diagnostic environments are defined by Artificial Intelligence Exchange and Service... Active Standard
1232.1-1997 - Artificial Intelligence Exchange and Service Tie to All Test Environments (AI-ESTATE): Data and Knowledge SpecificationFormal models for information used in system diagnosis are defined. As part of the AI-ESTATE (Artificial Intelligence Exchange and Service Tie to... Superseded Standard
1232.2-1998 - Artificial Intelligence Exchange and Service Tie to All Test Environments (AI-ESTATE): Service SpecificationFormal software interfaces to system diagnosis tools and applications are defined. As part of the AI-ESTATE set of standards, this standard... Superseded Standard
1232.3-2014 - Guide for the Use of Artificial Intelligence Exchange and Service Tie to All Test Environments (AI-ESTATE)Guidance to developers of IEEE Std 1232-conformant applications is provided in this guide. A simple doorbell is used as an example system under... Active Standard
1235-2000 - Guide for the Properties of Identifiable Jackets for Underground Power Cables and DuctsIdentification markings of jacketed underground power cables and ducts are established in this guide. Included are various methods of identifying... Active Standard
1241-2000 - Terminology and Test Methods for Analog-to-Digital ConvertersIEEE Std 1241-2000 identifies analog-to-digital converter (ADC) error sources and provides test methods with which to perform the required error... Superseded Standard
1241-2010 - Terminology and Test Methods for Analog-to-Digital ConvertersThe material presented in this standard is intended to provide common terminology and test methods for the testing and evaluation of analog-to... Active Standard
1277-2000 - Standard General Requirements and Test Code for Dry-Type and Oil-Immersed Smoothing Reactors for DC Power TransmissionThe electrical, mechanical, and physical requirements of oil-immersed and dry-type air core smoothing reactors for high-voltage direct current ... Superseded Standard
1277-2010 - Standard General Requirements and Test Code for Dry-Type and Oil-Immersed Smoothing Reactors for DC Power TransmissionThe electrical, mechanical, and physical requirements of oil-immersed and dry-type aircore smoothing reactors for high-voltage direct current ... Active Standard
1284-1994 - Standard Signaling Method for a Bidirectional Parallel Peripheral Interface for Personal ComputersA signaling method for asynchronous, fully interlocked, bidirectional parallel communications between hosts and printers or other peripherals is... Superseded Standard
1284-2000 - Standard Signaling Method for a Bidirectional Parallel Peripheral Interface for Personal ComputersA signaling method for asynchronous, fully interlocked, bidirectional parallel communi-cations between hosts and printers or other peripherals is... Active Standard
1286-1997 - 4.76 kV to 38 kV Rated Grounding and Testing Devices Used in EnclosuresDrawout type grounding and testing (G&T) devices for use in medium-voltage metal-clad switchgear rated above 4.76 kV through 38 kV are covered... Superseded Standard
1290-1996 - Guide for Motor Operated Valve (MOV) Motor Application, Protection, Control, and Testing in Nuclear Power Generating StationsMotors used to drive valve operators in nuclear power generating stations are discussed. Guidelines to evaluate the adequecy of motors used to... Active Standard
1293-1998 - Standard Specification Format Guide and Test Procedure for Linear, Single-Axis, Non-Gyroscopic AccelerometersThe specification and test requirements for a linear, single-axis, nongyroscopic accelerometer for use in inertial navigation, guidance, and... Active Standard
1293-1998/Cor 1-2008 - Standard Specification Format Guide and Test Procedure for Linear,Single-Axis, Nongyroscopic Accelerometers Corrigendum 1: Changes to Annex K and Annex LCorrigendum to IEEE Std 1293-1998. Specification and test requirements for linear, single-axis, nongyroscopic accelerometers for use as a sensor... Active Standard
Displaying results 321 - 360 of 685 - all results