Standard Icon

Instrumentation and Measurement Standards

Displaying results 201 - 240 of 803
Standard Name
Status Help less all
433-1974 - Recommended Practice for Insulation Testing of Large AC Rotating Machinery with High Voltage at Very Low FrequencyThis document provides a uniform method of VLF testing in order to obtain consistent results, accumulate meaningful experience, and lead to... Withdrawn Standard
433-2009 - Recommended Practice for Insulation Testing™ of AC Electric Machinery with High Voltage at Very Low FrequencyThis recommended practice describes very low frequency withstand and diagnostic tests that are performed on the stator windings of ac electric... Active Standard
436-1977 - Guide for Making Corona (Partial Discharge) Measurements on Electronics TransformersThis guide covers the detection of corona and the measurement of corona magnitude in electronics transformers. Test conditions, terminology, test... Superseded Standard
436-1991 - Guide for Making Corona (Partial Discharge) Measurements on Electronics TransformersA uniform procedure for making corona (partial discharge) measurements by electrical means on electronic transformers is presented. Methods of... Active Standard
449-1984 - Ferroresonant Voltage RegulatorsThis standard pertains to ferroresonant transformers used as regulators in electronic power supplies and in other equipment. Guides to application... Superseded Standard
449-1990 - Ferroresonant Voltage RegulatorsThis standard pertains to ferroresonant voltage regulators that operate at relatively constant frequencies and provide substantially constant... Withdrawn Standard
449-1998 - Ferroresonant Voltage RegulatorsFerroresonant transformers used as regulators in electronic power supplies and in other equipment are covered. Guides to application and test... Active Standard
450-1972 - Recommended Practice for Maintenance, Testing, and Replacement of Large Stationary Type Power Plant and Substation Lead Storage BatteriesProper maintenance will prolong the life of a battery and will aid in assuring that it is capable of supplying its design power requirements. A... Superseded Standard
450-1975 - Recommended Practice for Maintenance, Testing, and Replacement of Large Lead Storage Batteries for Generating Stations and SubstationsLarge stationary lead storage batteries play an ever increasing role in substation and generating station control systems and in providing the... Superseded Standard
450-1980 - Recommended Practice for Maintenance, Testing , and Replacement of Large Lead Storage Batteries for Generating Stations and SubstationsLarge stationary lead storage batteries play an ever increasing role in substation and generating station control and power systems and in... Superseded Standard
450-1987 - Recommended Practice for Maintenance,Testing, and Replacement of Large Lead Batteries for Generating Stations and SubstationsThis recommended practice is limited to providing recommended practices of maintenance, test schedules, and testing procedures than can be used to... Superseded Standard
450-1995 - Recommended Practice for Maintenance, Testing, and Replacement of Vented Lead-Acid Batteries for Stationary ApplicationsMaintenance, test schedules, and testing procedures that can be used to optimize the life and performance of permanently installed, vented lead... Superseded Standard
450-2002 - Recommended Practice for Maintenance, Testing , and Replacement of Vented Lead-Acid Batteries for Stationary ApplicationsMaintenance, test schedules, and testing procedures that can be used to optimize the life and performance of permanently installed, vented lead... Superseded Standard
450-2010 - Recommended Practice for Maintenance, Testing, and Replacement of Vented Lead-Acid Batteries for Stationary ApplicationsMaintenance, test schedules, and testing procedures that can be used to optimize the life and performance of permanently installed, vented lead... Active Standard
454-1973 - Recommended Practice for the Detection and Measurement of Partial Discharges (Corona) During Dielectric TestsThis document is based on IEC Publication 270-1968, Partial Discharge Measurements. adheres closely to the IEC recommendations with the following... Withdrawn Standard
455-1976 - Standard Test Procedure for Measuring Longitudinal Balance of Telephone Equipment Operating in the Voice BandTelephone companies and equipment manufacturers have generally agreed on a definition for longitudinal balance for many years. This agreement... Superseded Standard
455-1985 - Standard Test Procedure for Measuring Longitudinal Balance of Telephone Equipment Operating in the Voice BandThe purpose of this standard is threefold: to define the basic requirements of a test circuit which can be used to measure longitudinal balance.... Withdrawn Standard
460-1988 - Electrical Measuring Transducer for Converting AC Electrical Quantities into DC Electrical QuantitiesThis standard applies to measuring transducers used for converting AC electrical quantities such as current, voltage, power (active or reactive),... Withdrawn Standard
469-1988 - Recommended Practice for Voice-Frequency Electrical-Noise Tests of Distribution TransformersThe standard provides instruction for the testing of distribution transformers as sources of voice-frequency noise. These tests measure the degree... Withdrawn Standard
470-1972 - Standard Application Guide for Bolometric Power MetersThe purpose of this standard is to document the minimum information that users of bolometric power meters may need. It also provides potential... Withdrawn Standard
488.1-1987 - Standard Digital Interface for Programmable InstrumentationThe ANSI/IEEE Std 488.1-1987, IEEE standard digital interface for programmable instrumentation, deals with systems that use a byte-serial, bit... Superseded Standard
488.1-2003 - Higher Performance Protocol for the Standard Digital Interface for Programmable InstrumentationThis standard applies to interface systems used to interconnect both programmable and nonprogrammable electronic measuring apparatus with other... Active Standard
488.2-1992 - Standard Codes, Formats, Protocols, and Common Commands For Use with ANSI/IEEE Std 488.1-1987 IEEE Standard Digital Interface for Programmable InstrumentationA set of codes and formats to be used by devices connected via the IEEE 488.1 bus is specified. This standard also defines communication protocols... Superseded Standard
488.2-1992 - Standard Codes, Formats, Protocols, and Common Commands for Use With IEEE Std 488.1-1987, IEEE Standard Digital Interface for Programmable InstrumentationA set of codes and formats to be used by devices connected via the IEEE 488.1 bus is specified. This standard also defines communication protocols... Active Standard
495-1986 - Guide for Testing Faulted Circuit IndicatorsDefinitions, service conditions, test procedures, and conditions for faulted circuit indicators for use on power distribution systems are established. Withdrawn Standard
495-2007 - Guide for Testing Faulted Circuit IndicatorsDefinitions, service conditions, test procedures, and test conditions for faulted circuit indicators for use on power distribution systems are... Active Standard
498-1985 - Standard Requirements for the Calibration and Control of Measuring and Test Equipment Used in Nuclear FacilitiesThis standard sets forth the requirements for a calibration program to control and verify the accuracy of measuring and test equipment used to... Superseded Standard
498-1990 - Standard Requirements for the Calibration and Control of Measuring and Test Equipment Used in Nuclear FacilitiesThe standard sets forth the requirements for a calibration program to control and verify the accuracy of measuring and test equipment used to... Withdrawn Standard
501-1978 - Standard Seismic Testing of RelaysThis is a standard for developing data related to the seismic capabilities of relays. This standard compliments ANSI/IEEE Std 344-1975,... Superseded Standard
510-1983 - Recommended Practices for Safety in High-Voltage and High-Power TestingSafety practices for those who are involved with making measurements on high-voltage sources or with high-power sources of various types,... Withdrawn Standard
511-1979 - Standard on Video Signal Transmission Measurement of Linear Waveform DistortionThe standard describes methods for measuring the linear waveform distortions of TV video signals, that is, distortions which are caused by... Withdrawn Standard
515-1989 - Recommended Practice for the Testing, Design, Installation, and Maintenance of Electrical Resistance Heat Tracing for Industrial ApplicationsThis recommended practice provides recommendations for the testing, design, installation, and maintenance of electrical resistance heat tracing in... Superseded Standard
515-1997 - the Testing, Design, Installation and Maintenance of Electrical Resistance Heat Tracing for Industrial ApplicationsThe specific test requirements for qualifying electrical resistance heating cables for industrial service are provided, as well as the basis for... Superseded Standard
Displaying results 201 - 240 of 803 - all results