Standard Icon

Instrumentation and Measurement Standards

Displaying results 81 - 120 of 678
Standard Name
Status Help less all
252-1995 - Standard Test Procedure for Polyphase Induction Motors Having Liquid in the Magnetic GapIn this IEEE Standard instructions for conducting and reporting the more generally applicable and acceptable tests to determine the performance... Active Standard
255-1963 - Standard Letter Symbols for Semiconductor DevicesThis Standard provides a uniform system of letter symbols for electrical quantities and parameters as applied to semiconductor devices. It is... Withdrawn Standard
259-1974 - Standard Test Procedure for Evaluation of Systems of Insulation for Specialty TransformersThe intent of this standard is to establish a uniform method by which the life of specialty transformer insulation systems can be compared.... Superseded Standard
259-1994 - Standard Test Procedure for Evaluation of Systems of Insulation for Specialty TransformersA uniform method by which the thermal endurance of electrical insulation systems for dry-type specialty and general-purpose transformers can be... Superseded Standard
259-1999 - Standard Test Procedure for Evaluation of Systems of Insulation for Dry-Type Specialty and General-Purpose TransformersA uniform method by which the thermal endurance of electrical insulation systems for dry-type specialty and general-purpose transformers can be... Active Standard
260-1978 - Standard Letter Symbols for Units of Measurement (SI Units, Customary Inch-Pound Units, and Certain Other Units)Close cooperation of committees of the International Electrotechnical Commission, the International Organization for Standardization, and the SUN... Superseded Standard
260.1-1993 - American National Standard Letter Symbols for Units of Measurement (SI Units, Customary Inch-Pound Units, and Certain Other Units)General principles of letter symbol standardization are discussed. Symbols are given for general use and for use with limited character sets. The... Superseded Standard
260.1-2004 - Standard Letter Symbols for Units of Measurement (SI Customary Inch-Pound Units, and Certain Other Units)Letter symbols for units of measurement are covered in this standard. It does not include abbreviations for technical terms, nor does it cover... Active Standard
260.3-1993 - American National Standard Mathematical Signs and Symbols for Use in Physical Sciences and TechnologySigns and symbols used in writing mathematical text are defined. Special symbols peculiar to certain branches of mathematics, such as non... Active Standard
260.4-1996 - American National Standard Letter Symbols and Abbreviations for Quantities Used in AcousticsLetter symbols for physical quantities used in the science and technology of acoustics are covered. Abbreviations for a number of acoustical... Active Standard
268-1992 - American National Metric PracticeGuidance for the application of the modernized metric system in the United States is given. Known as the International System of Units (SI), the... Superseded Standard
270-2006 - Standard Definitions for Selected Quantities, Units, and Related Terms, with Special Attention to the International System of Units (SI)The definitions for physical quantities and units commonly used in applied science and technology, and for related terms that concern systems of... Active Standard
271-1966 - Technical Report on Switching Surge Testing of Extra-High-Voltage SwitchesThis standard provides guidance in the switching surge testing of EHV air switches. For the design and safe application of EHV air switches, it is... Superseded Standard
272-1970 - Computer-Type (Square-Loop) Pulse TransformersThis standard pertains to computer-type pulse transformers. These pulse transformers are characterized by their use of a 'square-loop' core... Withdrawn Standard
280-1985 - Standard Letter Symbols for Quantities Used in Electrical Science and Electrical EngineeringThe standard covers letter symbols used to represent physical quantities in electrical science and engineering. The general principles of letter... Active Standard
284-1968 - Standards Report on State-of-the-Art of Measuring Field Strength, Continuous Wave, SinusoidalThis document is a Report on the state-of-the-art of measuring field strength of radio-frequency electromagnetic waves, with respect to available... Withdrawn Standard
287-2007 - Precision Coaxial Connectors (DC to 110 GHz)This standard presents the combined efforts of IEEE Subcommittee P287 that reflect the knowledge and experience of leading specialists in the... Active Standard
290-1980 - Electric Couplings; Part I - General, Rating, Performance Characteristics; Part II - Test ProceduresElectric couplings are widely used to transmit mechanical torque from one rotating member to another. They are distinguished from mechanical... Withdrawn Standard
293-1969 - Test Procedure for Single-Degree-of-Freedom Spring-Restrained Rate GyrosThis test procedure is a compilation of recommended rate gyro test procedures derived from those currently in use, including test conditions to be... Active Standard
300-1988 - Standard Test Procedures for Semiconductor Charged-Particle DetectorsThis standard applies to semiconductor radiation detectors that are used for the detection and high-resolution spectroscopy of charged particles.... Active Standard
301-1988 - Standard Test Procedures for Amplifiers and Preamplifiers used with Detectors of Ionizing RadiationThis standard describes test procedures for amplifiers and preamplifiers that are used with semiconductor, scintillation, and proportional... Active Standard
304-1977 - Test Procedure for Evaluation and Classification of Insulation Systems for Direct-Current MachinesThis test procedure has been prepared to serve as a useful guide for the evaluation of insulation systems for direct-current machines and to... Withdrawn Standard
306-1969 - Test Procedure for Charging InductorsProvides standardised methods of determining the electrical parameters of charging inductors used in radar transmitters, linear particle... Withdrawn Standard
309-1970 - Standard Test Procedure for Geiger-Müller CountersThis publication presents standard test procedures for Geiger-Muller counter radiation detectors. These detectors, originally announced by ?Geiger... Superseded Standard
309/N42.3-1999 - Standard Test Procedures and Bases for Geiger-Mueller CountersTest procedures for Geiger-Mueller counters that are used for the detection of ionizing radiation are presented so that they have the same meaning... Active Standard
310-1969 - Reference-Standard Electrical ResistorsThis standard applies to precision electrical resistors exhibiting a high degree of stability and intended for use as reference standards in... Withdrawn Standard
311-1970 - Standard Specification of General-Purpose Laboratory Cathode-Ray OscilloscopesThe purposes of this Standard are: to document the minimum information that users of general-purpose laboratory cathode-ray oscilloscopes... Withdrawn Standard
315-1975 - Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Letters)A list of graphic symbols and class designation letters for use on electrical and electronics diagrams is provided. All of the symbols are... Active Standard
315A-1986 - Supplement to Graphic Symbols for Electrical and Electronics DiagramsGraphic symbols and information needed for use on electrical and electronic diagrams, which are internationally approved, are presented. Active Standard
316-1971 - Standard Requirements for Direct Current Instrument ShuntsThis standard applies to shunts for use in direct current circuits to extend the range of instruments or other measuring devices. This standard... Withdrawn Standard
319-1971 - Standard on Magnetostrictive Materials: Piezomagnetic NomenclatureThe purpose of this Standard is to make possible the comparison of the relative merits of magnetostrictive, electromagnetic, piezoelectric, and... Superseded Standard
319-1990 - Standard on Magnetostrictive Materials: Piezomagnetic NomenclatureThis standard serves to aid the comparison of the relative merits of magnetostrictive, electromagnetic, piezoelectric, and electrostrictive... Withdrawn Standard
325-1986 - Standard Test Procedures for Germanium Gamma-Ray DetectorsThe object of this standard is to establish standard test procedures for germanium gamma-ray detectors so that measurements have the same meaning... Withdrawn Standard
325-1996 - Standard Test Procedures for Germanium Gamma-Ray DetectorsTerminology and standard test procedures for germanium radiation detectors that are used for the detection and high-resolution spectrometry of... Active Standard
334-1974 - Type Tests of Continuous Duty Class 1E Motors for Nuclear Power Generating StationsSuperseded. Methods and requirements for qualifying continuous duty Class 1E motors for use in nuclear power generating stations are provided. The... Superseded Standard
334-1994 - Qualifying Continuous Duty Class 1E Motors for Nuclear Power Generating StationsMethods and requirements for qualifying continuous duty Class 1E motors for use in nuclear power generating stations are provided. The methods are... Superseded Standard
Displaying results 81 - 120 of 678 - all results