Standard Icon

Instrumentation and Measurement Standards

Displaying results 361 - 400 of 794
Standard Name
Status Help less all
1106-1995 - Recommended Practice for Installation, Maintenance, Testing, and Replacement of Vented Nickel-Cadmium Batteries for Stationary ApplicationsInstallation design, installation, maintenance and testing procedures, and test schedules that can be used to optimize the life and performance of... Superseded Standard
1106-2005 - Recommended Practice for Installation, Maintenance, Testing, and Replacement of Vented Nickel-Cadmium Batteries for Stationary ApplicationsThis recommended practice provides recommendations for installation design and for installation, maintenance, and testing procedures that can be... Superseded Standard
1106-2015 - Recommended Practice for Installation, Maintenance, Testing, and Replacement of Vented Nickel-Cadmium Batteries for Stationary ApplicationsThis recommended practice provides recommendations for installation design and for installation, maintenance, and testing procedures that can be... Active Standard
1122-1987 - Digital Recorders for Measurements in High-Voltage Impulse TestsThe object of this standard is to define the terms specifically related to the digital recorders used for monitoring high-voltage (HV) and high... Superseded Standard
1122-1998 - Digital Recorders for Measurements in High-Voltage Impulse TestsThis standard defines the terms specifically related to the digital recorders used for monitoring high-voltage and high-current impulse tests,... Active Standard
1131-1987 - Standard Cryostat End-Cap Dimensions for Germanium Semiconductor Gamma-Ray SpectrometersThis standard establishes fixed dimensions for end-caps in the interests of interchangeability of cryostats from various manufacturers. Seven... Withdrawn Standard
1138-1994 - Standard Construction of Composite Fiber Optic Groundwire (OPGW) for Use on Electric Utility Power LinesThe construction, mechanical and electrical performance, installation guidelines, acceptance criteria, and test requirements for a composite... Superseded Standard
1138-2009 - Testing and Performance for Optical Ground Wire (OPGW) for Use on Electric Utility Power LinesThis standard covers the performance, test requirements, procedures, and acceptance criteria for a transmission line overhead ground wire (a.k.a.... Active Standard
1138-2009/Cor 1-2014 - Testing and Performance for Optical Ground Wire (OPGW) Use on Electric Utility Power Lines -- Corrigendum 1: Stress-Strain Temperature Correction, Aeolian Vibration VelocityThis corrigendum corrects the temperature associated with the Stress-Strain clause; and corrects the use of the term velocity in the Aeolian... Active Standard
1139-1988 - Standard Definitions of Physical Quantities for Fundamental Frequency and Time MetrologyThis standard covers the fundamental metrology for describing physical quantities of importance to frequency and time metrology. Quantities... Withdrawn Standard
1139-1999 - Standard Definitions of Physical Quantities for Fundamental Frequency and Time Metrology-Random InstabilitiesMethods of describing random instabilities of importance to frequency and time metrology is covered in this standard. Quantities covered include... Superseded Standard
1139-2008 - Standard Definitions of Physical Quantities for Fundamental Frequency and Time Metrology--Random InstabilitiesMethods of describing random instabilities of importance to frequency and time metrology are covered. Quantities covered include frequency,... Active Standard
1142-1995 - Guide for the Design, Testing, and Application of Moisture-Impervious, Solid Dielectric, 5-35 kV Power Cable Using Metal-Plastic LaminatesIn this IEEE Standard the user of underground cables is provided with information on the design, testing, and application of moisture-impervious,... Withdrawn Standard
1142-2009 - Guide for the Selection, Testing, Application, and Installation of Cables having Radial-Moisture Barriers and/or Longitudinal Water BlockingDetailed information relating to the design, testing, application and installation of various types of electrical cables in order to prevent the... Active Standard
1149.1-1990 - Standard Test Access Port and Boundary-Scan ArchitectureIEEE Std. 1149.1-1990, defines circuitry that may be built into an integrated circuit to assist in the test, maintenance, and support of assembled... Superseded Standard
1149.1-2001 - Standard Test Access Port and Boundary Scan ArchitectureCircuitry that may be built into an integrated circuit to assist in the test, maintenance, and support of assembled printed circuit boards is... Superseded Standard
1149.1-2013 - Test Access Port and Boundary-Scan ArchitectureCircuitry that may be built into an integrated circuit to assist in the test, maintenance and support of assembled printed circuit boards and the... Active Standard
1149.1a-1993 - Supplement to Standard Test Access Port and Boundary-Scan Architecture (1149.1) A test access port and boundary-scan architecture for digital integrated circuits and for the digital portions of mixed analog/digital integrated... Superseded Standard
1149.1b-1994 - Supplement to Standard Test Access Port and Boundary-Scan Architecture (1149.1)A language to describe components that conform to IEEE Std 1149.1-1990 is described. The language is based on the VHSIC Hardware Description... Superseded Standard
1149.4-1999 - a Mixed-Signal Test BusThe testability structure for digital circuits described in IEEE Std 1149.1-1990 has been extended to provide similar facilities for mixed-signal... Superseded Standard
1149.4-2010 - a Mixed-Signal Test BusThe testability structure for digital circuits described in IEEE Std 1149.1-2001 has been extended to provide similar facilities for mixed-signal... Active Standard
1149.5-1995 - Module Test and Maintenance Bus (MTM-Bus) ProtocolThis standard specifies a serial, backplane, test and maintenance bus (M™-Bus) that can be used to integrate modules form different teams or... Withdrawn Standard
1149.6-2003 - Boundary-Scan Testing of Advanced Digital NetworksThis standard augments IEEE Std 1149.1 to improve the ability for testing differential and/or ac-coupled interconnections between integrated... Superseded Standard
1149.6-2015 - Approved Draft Boundary-Scan Testing of Advanced Digital NetworksThis standard augments IEEE Std 1149.1 to improve the ability for testing differential and/or ac-coupled interconnections between integrated... Active Standard
1149.7-2009 - Reduced-Pin and Enhanced-Functionality Test Access Port and Boundary-Scan ArchitectureThis specification describes circuitry that may be added to an integrated circuit to provide access to on-chip Test Access Ports (TAPs) specified... Active Standard
1155-1992 - VMEbus Extensions for Instrumentation: VXIbusA technically sound modular instrument standard based on IEEE Std 1014-1987, which is open to all manufacturers and is compatible with present... Active Standard
1160-1993 - Standard Test Procedures for High-Purity Germanium Crystals for Radiation DetectorsThis standard applies to the measurement of bulk properties of high-purity germanium as they relate to the fabrication and performance of... Active Standard
1174-2000 - Standard Serial Interface for Programmable InstrumentationA serial, full-duplex, asynchronous, 9-pin data terminal equipment (DT ) communications port for programmable instrumentation that follows ANSI... Active Standard
1177-1993 - FASTBUS Standard Routines1177-1993 Abstract: Standard software routines for use with the system in IEEE Std 960-1993 are defined. 960-1993 Abstract: Mechanical, signal,... Superseded Standard
1181-1991 - Recommended Practice for Latchup Test Methods for CMOS and BiCMOS Integrated- Circuit Process CharacterizationRecommendations are provided for the layout and test methods required to characterize properly latchup behavior in CMOS and BiCMOS integrated... Withdrawn Standard
1188-1996 - Recommended Practice for Maintenance, Testing, and Replacement of Valve- Regulated Lead-Acid (VRLA) Batteries for Stationary ApplicationsIn this IEEE standard maintenance, test schedules, and testing procedures that can be used to optimize the life and performance of valve-regulated... Superseded Standard
1188-2005 - Recommended Practice for Maintenance, Testing, and Replacement of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary ApplicationsThis recommended practice is limited to maintenance, test schedules, and testing procedures that can be used to optimize the life and performance... Active Standard
1188a-2014 - Recommended Practice for Maintenance, Testing, and Replacement of Valve-Regulated Lead-Acid (VRLA) Batteries for Stationary Applications - Amendment 1: Updated VRLA Maintenance ConsiderationsNew guidance to users dealing with premature capacity failures with VRLA batteries and updated definitions are addressed in this amendment. Active Standard
1193-1994 - Guide for Measurement of Environmental Sensitivities of Standard Frequency GeneratorsStandard frequency generators that include all atomic frequency standards and precision quartz crystal oscillators are addressed. There are three... Superseded Standard
1193-2003 - Guide for Measurement of Environmental Sensitivities of Standard Frequency GeneratorsStandard frequency generators that include all atomic frequency standards, quartz oscillators, dielectric resonator oscillators, yttrium-iron... Active Standard
1202-1991 - Flame Testing of Cables for Use in Cable Tray in Industrial and Commercial OccupanciesA test protocol and the performance criteria to determine the flame propagation tendency of cables in a vertical cable tray are presented. They... Superseded Standard
1202-2006 - Flame-Propagation Testing of Wire & CableStandardization of cable flame propagation testing is beneficial to cable manufacturers, distributors, and users. Uniform procedures; consistent,... Active Standard
1202-2006/Cor 1-2012 - Flame-Propagation Testing of Wire and Cable - Corrigendum 1Corrected English unit conversions are included in this corrigendum to IEEE Std 1202-2006. Active Standard
1210-1996 - Standard Tests for Determining Compatibility of Cable-Pulling Lubricants With Wire and CableCriteria and test methods for determining the compatibility of cable-pulling lubricants (compounds) with cable jacket or other exterior cable... Superseded Standard
1210-2004/Cor 1-2014 - Standard Tests for Determining Compatibility of Cable-Pulling Lubricants with Wire and Cable - Corrigendum 1Criteria and test methods for determining the compatibility of cable-pulling lubricants (compounds) with cable jacket or other exterior cable... Active Standard
Displaying results 361 - 400 of 794 - all results