Project Icon

Electromagnetic Compatibility Standards

Displaying results 41 - 80 of 102
1 2 3
Electromagnetic Compatibility Standards
1302-2008 - IEEE Guide for the Electromagnetic Characterization of Conductive Gaskets in the Frequency Range of DC to 18 GHzThe scope of the proposed project is to provide manufacturers of gaskets and designers of electronic systems appropriate methods for the ... active Standard
1309-2013 - IEEE Standard for Calibration of Electromagnetic Field Sensors and Probes (Excluding Antennas) from 9 kHz to 40 GHzConsensus calibration methods for electromagnetic (EM) field sensors and probes are provided. Data recording and reporting requirements ... active Standard
1363.1-2008 - IEEE Standard Specification for Public Key Cryptographic Techniques Based on Hard Problems over LatticesSpecifications of common public-key cryptographic techniques based on hard problems over lattices supplemental to those considered in IE ... active Standard
1460-1996 - IEEE Guide for the Measurement of Quasi-Static Magnetic and Electric FieldsA listing of possible measurement goals related to characterizing quasi-static magnetic and electric fields and possible methods for the ... active Standard
1490-2011 - IEEE Guide--Adoption of the Project Management Institute (PMI(R)) Standard A Guide to the Project Management Body of Knowledge (PMBOK(R) Guide)--Fourth EditionThe PMI standard, A Guide to the Project Management Body of Knowledge (PMBOK(R) Guide)--Fourth Edition, is adopted in this standard. (NO ... withdrawn Standard
1502-2007 - IEEE Recommended Practice for Radar Cross-Section Test ProceduresThis recommended practice describes the process of the measurement of the radar cross section of objects using a test range. The term †... active Standard
1549-2011/Cor 1-2017 - IEEE Approved Draft Standard for Microwave Filter Definitions--Corrigendum 1Standardized definition of terms commonly used in the field of electrical networks and filters are defined. active Standard
1560-2005 - IEEE Standard for Methods of Measurement of Radio Frequency Power Line Interference Filter in the Range of 100 Hz to 10 GHzUniform methods of measurements of radio-frequency power-line interference filter attenuation performance in the range of 100 Hz to 10 G ... active Standard
1581-2011 - IEEE Standard for Static Component Interconnection Test Protocol and ArchitectureIEEE Std 1581 defines a low-cost method for testing the interconnection of discrete, complex memory integrated circuits (ICs) where addi ... active Standard
1597.1-2008 - IEEE Standard for Validation of Computational Electromagnetics Computer Modeling and SimulationsThis standard defines a method to validate computational electromagnetics computer modeling and simulation techniques, codes, and models ... active Standard
1597.2-2010 - IEEE Recommended Practice for Validation of Computational Electromagnetics Computer Modeling and SimulationsThis recommended practice is a companion document for IEEE Std 1597.1-2008. Examples and problem sets to be used in the validation of co ... active Standard
1615-2007 - IEEE Recommended Practice for Network Communication in Electric Power SubstationsRecommended practices for communication and interoperation of devices connected on an electric power substation Internet protocol (IP) n ... active Standard
1642-2015 - IEEE Recommended Practice for Protecting Publicly Accessible Computer Systems from Intentional Electromagnetic Interference (IEMI)Appropriate electromagnetic threat levels, protection methods, monitoring techniques, and test techniques for specific classes of comput ... active Standard
1688-2015 - IEEE Standard Requirements for the Control of Electromagnetic Interference Characteristics of Replaceable Electronic ModulesElectromagnetic performance requirements for replaceable electronic modules (REMs) are specified. This standard is suitable for items th ... active Standard
1720-2012 - IEEE Recommended Practice for Near-Field Antenna MeasurementsNear-field test practices for the measurement of antenna properties are described in this document and near-field measurement practices ... active Standard
1785.1-2012 - IEEE Standard for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and Above—Part 1: Frequency Bands and Waveguide DimensionsSpecifications for the waveguide (including aperture dimensions, frequency range, cutoff frequency, etc.) are given in this standard. Th ... active Standard
1785.2-2016 - IEEE Standard for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and Above—Part 2: Waveguide InterfacesSpecifications for rectangular waveguide interfaces are given in this standard. It considers the tolerances of the waveguide interface d ... active Standard
1785.3-2016 - IEEE Recommended Practice for Rectangular Metallic Waveguides and Their Interfaces for Frequencies of 110 GHz and Above—Part 3: Recommendations for Performance and Uncertainty SpecificationsRecommendations for summarizing the performance and the expected uncertainty of the reflection coefficient of rectangular-waveguide aper ... active Standard
1900.2-2008 - IEEE Recommended Practice for the Analysis of In-Band and Adjacent Band Interference and Coexistence Between Radio SystemsThis recommended practice will provide technical guidelines for analyzing the potential for coexistence or in contrast interference betw ... active Standard
1900.4-2009 - IEEE Standard for Architectural Building Blocks Enabling Network-Device Distributed Decision Making for Optimized Radio Resource Usage in Heterogeneous Wireless Access NetworksThe standard defines the building blocks comprising (i) network resource managers, (ii) device resource managers, and (iii) the informat ... active Standard
3003.2-2014 - IEEE Recommended Practice for Equipment Grounding and Bonding in Industrial and Commercial Power SystemsThe grounding and bonding of equipment in industrial and commercial power systems is covered in this recommended practice. The interconn ... active Standard
11073-10102-2012 - Health informatics — Point-of-care medical device communication Part 10102: Nomenclature —Annotated ECGThe base IEEE 11073-10101 Nomenclature is extended by this standard to provide support for ECG annotation terminology. It may be used ei ... active Standard
11073-10418-2011/Cor 1-2015 - IEEE Health informatics--Personal health device communication Part 10418: Device specialization--International Normalized Ratio (INR) monitor - Corrigendum 1A normative definition of communication between personal telehealth International Normalized Ratio (INR) devices (agents) and managers ( ... active Standard
24748-4-2016 - ISO/IEC/IEEE International Standard for Systems and Software Engineering -- Life Cycle Management -- Part 4: Systems Engineering PlanningThe evolution of the harmonized set of ISO/IEC/IEEE 15288-12207 related standards and technical reports that are discussed in this Inter ... active Standard
C63.2-2016 - American National Standard for Specifications of Electromagnetic Interference and Field Strength Measuring Instrumentation in the Frequency Range 9 kHz to 40 GHzRequirements for measuring instruments used for electromagnetic interference (EMI) measurements are provided, involving quasi-peak, peak ... active Standard
C63.4-2014 - American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHzANSI C63.4, conducted emission testing, conducting ground plane, digital equipment, electric field measurement, line impedance stabiliza ... active Standard
C63.4a-2017 - American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz Amendment 1: Test Site ValidationU.S. consensus standard methods are specified in Annex D of this amendment for validating standard test sites and alternative test sites ... active Standard
C63.5-2017 - American National Standard for Electromagnetic Compatibility--Radiated Emission Measurements in Electromagnetic Interference (EMI) Control--Calibration and Qualification of Antennas (9 kHz to 40 GHz)Methods for determining antenna factors of antennas used for radiated emission measurements in electromagnetic interference (EMI) contro ... active Standard
C63.7-2015 - American National Standard Guide for Construction of Test Sites for Performing Radiated Emission MeasurementsInformation that is useful in constructing test sites used to perform radiated emission measurements in the frequency range of 30 MHz to ... active Standard
C63.9-2008 - American National Standard for RF Immunity of Audio Office Equipment to General Use Transmitting Devices with Transmitter Power Levels up to 8 WattsDraft Version 3.4. This standard provides recommended test methods and limits for assuring the RF immunity of office equipment to genera ... active Standard
C63.10-2013 - American National Standard of Procedures for Compliance Testing of Unlicensed Wireless DevicesThe procedures for testing the compliance of a wide variety of unlicensed wireless transmitters (also called intentional radiators and l ... active Standard
C63.011-2000 - American National Standard for Limits and Methods of Measurement of Radio Disturbance Characteristics of Industrial, Scientific, and Medical (ISM) Radio-Frequency EquipmentThis standard republishes CISPR 11:1997 (with Amendment 1,1999-05)as an AmericanNational Standard to make it easily available to ... active Standard
C63.12-2015 - American National Standard Recommended Practice for Electromagnetic Compatibility Limits and Test LevelsA rationale and recommendations for developing emission limits and immunity test levels are presented in this recommended practice. Thes ... active Standard
C63.13-1991 - American National Standard Guide on the Application and Evaluation of EMI Power-Line Filters for Commercial UseA basic understanding of the application, evaluation, and safety considerations of electromagnetic interference (EMI) power-line filters ... active Standard
C63.14-2014 - American National Standard Dictionary of Electromagnetic Compatibility (EMC) including Electromagnetic Environmental Effects (E3)Terms associated with electromagnetic compatibility (EMC) and electromagnetic environmental effects (E3) are defined including electroma ... active Standard
C63.15-2010 - American National Standard Recommended Practice for the Immunity Measurement of Electrical and Electronic EquipmentThis immunity measurement and measurement instrumentation specification document complements the recommended procedures for making emiss ... active Standard