Project Icon

Power and Energy Projects

Displaying results 1 - 40 of 257
Project Name
P11 - Rotating Electric Machinery for Rail and Road Vehicles The purpose of this standard is to define ratings, tests, and calculation procedures to permit comparison among machines for similar use, and to... Active Project
P48 - Test Procedures and Requirements for Alternating-Current Cable Terminations Used on Shielded Cables Having Laminated Insulation Rated 2.5 kV through 765 kV or Extruded Insulation Rated 2.5 kV through 500 kV This standard provides test procedures and requirements for all indoor and outdoor cable terminations used on alternating-current shielded cables... Active Project
P56 - Draft Guide for Insulation Maintenance of Electric Machines This insulation maintenance guide is applicable to rotating electric machines rated from 35 KVA and higher. The procedures detailed herein may... Active Project
P81 - Guide for Measuring Earth Resistivity, Ground Impedance, and Earth Surface Potentials of a Grounding System The purpose of this guide is to present practical instrumentation methods that may be used for measuring soil resistivity, the impedance to remote... Active Project
P112 - Draft Standard Test Procedure for Polyphase Induction Motors and Generators Instructions for conducting and reporting the more generally applicable and acceptable tests of polyphase induction motors and generators are covered. Active Project
P115 - Guide for Test Procedures for Synchronous Machines Part I-Acceptance and Performance Testing Part II-Test Procedures and Parameter Determination for Dynamic Analysis This guide contains instructions for conducting generally applicable and accepted tests to determine the performance characteristics of... Active Project
P125 - Recommended Practice for Preparation of Equipment Specifications for Speed-Governing of Hydraulic Turbines Intended to Drive Electric Generators This recommended practice is intended to assist users with the preparation of procurement specifications for electric-hydraulic speed governors. Active Project
P352 - Draft Guide for General Principles of Reliability Analysis of Nuclear Power Generating Station Systems and Other Nuclear Facilities This guide provides the designers, operators, and regulators with a common and consistent framework for performance of reliability and... Active Project
P378 - Recommended Practices for Scattering Parameter Measurements Using Vector Network Analyzers Provide definitions of terms commonly used by users and manufacturers of vector network analyzers. Define and describe measurement techniques,... Active Project
P384 - Standard Criteria for Independence of Class 1E Equipment and Circuits This standard establishes the criteria for implementation of the independence requirements of IEEE Std 308(TM) 1 and IEEE Std 603(TM). Active Project
P386 - Draft Separable Insulated Connector Systems for Power Distribution Systems rated 2.5 kV through 35 kV Definitions, service conditions, ratings, interchangeable construction features, and tests are established for loadbreak and deadbreak separable... Active Project
P387 - Standard Criteria for Diesel-Generator Units Applied as Standby Power Supplies for Nuclear Power Generating Stations This standard provides the principal design criteria, the design features, testing, and qualification requirements for the individual diesel... Active Project
P388 - Transformers and Inductors in Electronic Power Conversion Equipment This standard pertains to transformers and inductors of both the saturating and nonsaturating type that are used in electronic power conversion... Active Project
P389 - Recommended Practice for Testing Transformers and Inductors For Electronics Applications This recommended practice presents a number of tests for use in determining the significant parameters and performance characteristics of... Active Project
P400.3 - Guide for Partial Discharge Field Diagnostic Testing of Shielded Power Cable Systems This guide describes diagnostic methods capable of detecting and locating partial discharges from defects and damage in installed shielded power... Active Project
P421.1 - Standard Definitions for Excitation Systems for Synchronous Machines This standard provides a common base for terminology in common usage related to excitation control systems. The definitions given in this standard... Active Project
P421.5 - Draft Recommended Practice for Excitation System Models for Power System Stability Studies Excitation system and power system stabilizer models suitable for use in large-scale system stability studies are presented. Important excitation... Active Project
P421.6 - Draft Recommended Practice for the Specification and Design of Field Discharge Equipment for Synchronous Machines This document is intended to serve as basic reference for the specification and design of field discharge circuits for synchronous machines. It is... Active Project
P430 - Draft Standard Procedures for the Measurement of Radio Noise from Overhead Power Lines and Substations This standard establishes uniform procedures for the measurement of radio noise generated by corona from overhead power lines. Measurement... Active Project
P433 - Recommended Practice for Insulation Testing of AC Electric Machinery with High Voltage Rating up to 30 kV at Very Low Frequency This document describes very low frequency (VLF) testing of ac electric machines. It covers acceptance testing of new machines in the factory or... Active Project
P442 - Guide for Soil Thermal Resistivity Measurement The purpose of this guide is to provide sufficient information to enable the user to select useful commercial test equipment, or to manufacture... Active Project
P484 - Draft Recommended Practice for Installation Design and Installation of Vented Lead-Acid Batteries for Stationary Applications Recommended design practices and procedures for storage, location, mounting, ventilation, instrumentation, pre-assembly, assembly, and charging of... Active Project
P485 - Recommended Practice for Sizing Lead-Acid Batteries for Stationary Applications Methods for defining the direct current (dc) load and for sizing a lead-acid battery to supply that load for stationary battery applications in... Active Project
P497 - Draft Standard Criteria for Accident Monitoring Instrumentation for Nuclear Power Generating Stations Criteria are established in this standard for variable selection, performance, design, and qualification of accident monitoring instrumentation... Active Project
P516 - Guide for Maintenance Methods on Energized Power Lines The purpose of this guide is to a) Present, in one guide, sufficient details of some of the methods and equipment presently in use to enable the... Active Project
P519.1 - Guide for Applying Harmonic Limits on Power Systems There is a need for guidelines that describe how the limits from IEEE 519-2014 can be applied in different situations. This document provides... Active Project
P524 - Draft Guide to the Installation of Overhead Transmission Line Conductors General recommendations for the selection of methods, equipment, and tools that have been found to be practical for the stringing of overhead... Active Project
P525 - Draft Guide for the Design and Installation of Cable Systems in Substations The design, installation, and protection of wire and cable systems in substations are covered in this guide, with the objective of minimizing... Active Project
P532 - Guide for Selecting and Testing Jackets for Power, Instrumentation, and Control Cables The guide provides cable users assistance in the selection of jackets for the purpose of optimizing cable design and performance. A secondary... Active Project
P563 - Guide on Conductor Self-Damping Measurements This Guide provides proven methods for investigators to perform measurements of the inherent damping characteristics of conductors. It defines... Active Project
P603 - Standard Criteria for Safety Systems for Nuclear Power Generating Stations The criteria contained in this standard establish minimum functional and design requirements for the power, instrumentation, and control portions... Active Project
P605 - Guide for Bus Design in Air Insulated Substations Substation rigid and strain bus structure design involves electrical, mechanical, and structural considerations. It is the purpose of this guide... Active Project
P627 - Qualification of Equipment Used in Nuclear Facilities The purpose of this standard is to provide basic principles and guidance to demonstrate the qualification of equipment. Qualification is intended... Active Project
P644 - Standard Procedures for Measurement of Power Frequency Electric and Magnetic Fields from AC Power Lines The purpose of this standard is to establish uniform procedures for the measurement of electric and magnetic field levels from overhead ac power... Active Project
P650 - Qualification of Class 1E Static Battery Chargers, Inverters and Uninterruptible Power Supply (UPS) Systems for Nuclear Power Generating Stations The purpose of this standard is to provide specific procedures to meet the equipment qualification requirements of IEEE Std 323 for battery... Active Project
P656 - the Measurement of Audible Noise from Overhead Transmission Lines The purpose of this standard is to establish uniform procedures for the measurement of audible noise from overhead transmission lines, using... Active Project
P664 - Guide for Laboratory Measurement of the Power Dissipation Characteristics of Aeolian Vibration Dampers for Single Conductors This guide describes the current methodologies, including apparatus, procedures, and measurement accuracies, for the testing of vibration dampers.... Active Project
P690 - Draft the Design and Installation of Cable Systems for Class 1E Circuits in Nuclear Power Generating Stations This standard provides direction for the design and installation of safety-related electrical cable systems, including associated circuits, in... Active Project
P693 - Recommended Practice for Seismic Design of Substations This recommended practice is for new substations and planned additions or improvements to existing substations. It is not intended that existing... Active Project
P741 - Draft Standard Criteria for the Protection of Class 1E Power Systems and Equipment in Nuclear Power Generating Stations Criteria that establish protection requirements for Class 1E power systems and equipment are prescribed in this standard. The purpose of and the... Active Project
Displaying results 1 - 40 of 257 - all